Search
dnt0212.jpg View Larger Image (in new window)

Lectrosonics : DNT0212

By: Lectrosonics
http://www.avsupply.com/images/logos/lectrosonics-logo.gif
Wireless Microphones & Audio Processors
Contact us for lowest price (800) 284-2288, (858) 565-1101, sales@avsupply.com, or fax (858) 300-4193
DANTE INTERFACE, 2 IN, 12 OUT

The Lectrosonics DNT0212 processor subscribes to channels on a Dante network and delivers them to an internal digital matrix for automatic mixing and processing, and to Dante network transmit channels. In addition, two analog line level inputs are provided for use with local sources audio sources such as voice evacuation announcements.

The outputs of the matrix can be assigned to a Dante transmit channel, an analog output and/or routed back to an input to be further mixed and processed with another input channel or matrix mix.

DNT0212 features include:

  • 32 inputs from DanteTM receive channels
  • 2 analog line level inputs
  • 16 outputs to DanteTM transmit channels
  • 8 line level analog outputs
  • 4 mic/line level analog outputs
  • Supports both switched and redundant modes in DanteTM operation
  • Post-mixing signal processing on all inputs (analog and digital)
  • 48 independent automatic mixers with 38 inputs per mixer and channel activity detectors
  • Support for multi-level mixing: mixes can be looped back and used as mixer inputs
  • Extensive signal processing including filters, delay and channel linking for dynamic processing
    (compressors, limiters)
  • Gain smoothing to prevent transient noise during instantaneous level changes
  • Four test signal generators available for system setup and testing
  • Extensive macro command language
  • Control interfaces via USB, RS-232, Ethernet and programmable logic I/O
  • Rack mount or under table mount
Audio Inputs (Balanced microphone/line level inputs with digitally programmable gain may be configured as unbalanced inputs)
Audio Input Channels
Digital: 32 Dante channels
Analog: 2 line level analog (for paging)
Gain: -20 dB to +20 dB
Impedance: 15kΩ differential, 3.75kΩ common
Maximum Analog Input Level: 20 dBu
Dynamic Range: 102 dB
THD + Noise: 0.01%
A-D Sampling Rate: 48 kHz, fixed
Audio Outputs Digital: 16 Dante transmit channels
Analog: 12 channels
Level: 0 dBu nominal
Impedance: <50Ω source to drive 600Ω minimum load
Channels 9~12 include 20 dB and 40 dB attenuators
Dante Interface Provides dual RJ-45 connectors on the rear panel and an Ethernet switch built into the processor
Supported Sampling Rate: 48 kHz
Data Rate LED: 100 Mbps/1 Gbps
Activity LED: Blinks when active
Modes of Operation
Switched mode using either connector
Redundant mode with primary and secondary networks using both connectors
Network Connectivity Dante interface and Ethernet control can be connected to the same network
Filters All filters have zero processing delay
EQ Stages: 4 per input channel
Internal Signal Generator Swept Sine
Modes: Single sweep, continuous sweep
Waveforms: Sawtooth (up or down), triangle
Sweep Rate: Linear, logarithmic
Parameters: Start freq, stop freq, level (dBu), sweep time (sec)
White Noise Parameter: Level (dBu)
Pink Noise Parameter: Level (dBu)
Tone (Sine Wave) Parameters: Level (dBu), frequency
Filter Type Low Pass
Butterworth 6, 12, 18, 24 dB/octave
Bessel 6, 12, 18, 24 dB/octave
Linkwitz-Riley 12, 24 dB/octave
Additional Parameters: Frequency (Hz)
High Pass
Butterworth 6, 12, 18, 24 dB/octave
Bessel 6, 12, 18, 24 dB/octave
Linkwitz-Riley 12, 24 dB/octave
Additional Parameters: Frequency (Hz)
Low Shelving
Butterworth 6, 12, 18, 24 dB/octave
Bessel 6, 12, 18, 24 dB/octave
Additional Parameters: Frequency (Hz), boost/cut (dB)
High Shelving
Butterworth 6, 12, 18, 24 dB/octave
Bessel 6, 12, 18, 24 dB/octave
Additional Parameters: Frequency (Hz), boost/cut (dB)
Peaking EQ Parametric
Parameters: Frequency (Hz), bandwidth (octave), boost/cut (dB)
Compressor Soft knee with RMS level detector eliminates need for separate attack and delay settings
0.1 ms increments
1 second maximum
Continuously adjustable ratio
Power Requirements 100~240 VAC, 50/60 Hz 20 W maximum consumption
Dimensions (WxDxH) 19 x 7.7 x 1.75" (483 x 196 x 44 mm)
Weight 5.3 lb (1.7 kg)


facebook.png twitter.png googleplus.png linkedin.png youtube.png pinterest.png
Prices and specifications subject to change without notice.