Video/Power transmission Solutions
Contact us for lowest price (800) 284-2288, (858) 565-1101,, or fax (858) 300-4193
16-Channel Power Supply StubEQ Active Receiver Hub

The NVT 16-Channel Power Supply StubEQ Active Receiver Hub NV-16PS42-PVD is a key hybrid component that consolidates all CCTV system cabling using standard EIA/TIA 568B structured building wiring. Designed for installation in the IDF/Telecom Closet or MDF/Equipment Room, Power Supply StubEQ™ Active Receiver Hubs have individual floating 28VAC outputs that support at-distance camera loads up to 1 Amp per channel for cable runs up to 1,500ft (460m). A built-in StubEQ™ video receiver hub ensures a zero loss video signal for connection into a DVR or IP encoder. The NV-16PS42-PVD standard features include: automatic-reset fault protection, transient protection, ground loop free individually floating outputs and power and video diagnostics. All NVT products are UL and cUL listed, are compliant with CE, RoHS, WEEE, and come with NVT’s lifetime warranty.

NV-16PS42-PVD features include:

→ Provides Class 2 SELV 28 VAC with up to 1 Amp/channel while receiving video transmission and delivering P/T/Z telemetry, all over a single 4-pair Cat5cable for each camera
→ Built-in distribution amplifier with 2 video outputs per channel
→ Full motion CCTV video at distances up to 1,500ft (460m) when used with any passive NVT transceiver
→ Adaptive StubEQ fully automatic 2-band equalization provides adjustment free equalization every time, no manual adjustments required
→ Frequency Response DC to 10 MHz
→ Automatic-reset fault protection; transient protection
→ Individually floating power outputs and differential video inputs ensure total ground-loop immunity
→ Diagnostic LEDs show load/no load, miswires, overload conditions, and video status
→ Limited lifetime warranty

Video Frequency response DC to 10 MHz
Video Attenuation 0.5 dB typ
Video Common-mode / Differential-mode rejection 15 KHz to 5 MHz 60 dB typ
Video Impedance Coax, female BNC 75 ohms
Video Impedance UTP, RJ45 100 ohms
Video Network Wiring One four-pair Category cable
Camera Power Each camera is powered by a fully isolated (floating) 28VAC Class 2SELV output at up to 1 Amp. Individually thermistor protected for auto-reset
Power inlet IEC with molded power cord (included)
Voltage 115 / 230V
Current 3.0 / 1.5 Amps
Protection 5x20mm type T fuse 5 Amp 250V
Wattage 500 Watts
Heat (NV-16PS42-PVD only) 275 BTU / Hour; (NV-16PS42-PVD with cameras:) 2,000 BTU / Hour
Ambient Temperature -4 to 122 °F (-20 to 50 °C)
Minimum airflow 4ft3/min (0,1m3/min)
Humidity (non-condensing) 0 to 95%
Transient Immunity per ANSI / 587 C62.41
Dimensions, including connectors 19in wide, 1.73in high, 12in deep, 43cm wide, 4,5cm high, 30cm deep
Product Weight 23.5lb (10,66kg)
Packaged Weight 32lb (14,5kg)
Mounting included Rack mount “L” brackets for front, rear, or wall installations; rubber feet for desk applications
Cables included Sixteen 2ft (60cm) coax jumpers, Molded IEC power inlet cord 7ft (200cm)
Mounting Optional NV-RMBK2 Rear Mount Support Kit(designed for use with thinner metal equipment racks) NV-WMBK2 Wall Mount Bracket Kit (heavy duty)


facebook.png twitter.png googleplus.png linkedin.png youtube.png pinterest.png
Prices and specifications subject to change without notice.