JAI AD-081GE High Dynamic Range 2-monochrome CCDs GigE Vision Camera

→ 2-monochrome prism-mounted progressive scan CCDs (1/3")
→ Member of the C3 Advanced series
→ 1024 (h) x 768 (v) active pixels per channel
→ 4.65 micro m square pixels
→ 30 frames/second with full resolution
→ 60 frames/second for interleaved high frame rate operation
→ Increased frame rates with partial scan or vertical binning
→ PIV (Particle Image Velocimetry) mode also available
→ Programmable exposure from 20 micro s to 33 m s
→ Auto shutter and GenICam Exposure Time Abs modes
→ Exposure time up to 2 sec. using Pulse Width trigger mode
→ Sequence trigger mode for on-the-fly change of gain, exposure and ROI
→ LVAL synchronous/asynchronous operation (auto-detect)
→ Programmable GPIO with opto-isolated inputs and outputs
→ Two I/O connectors configurable for separate or combined output
→ Comprehensive control tool and SDK for Windows XP /Vista
→ Sensor 1: 1/3" Monochrome IT CCD (ICX204AL)
→ Sensor 2: 1/3" Monochrome IT CCD (ICX204AL)
→ Pixel Clock: 33.75 MHz
→ Frame rate (HDR mode): 30 frames/sec.
→ Frame rate (interleaved): 60 frames/sec.
→ Active area: 4.76 (h) x 3.57 (v) mm
→ Cell size: 4.65 (h) x 4.65 (v) micro m
→ Active pixels: 1024 (h) x 768 (v)
→ Read-out modes, Full: 1024 (h) x 768 (v) 30/60 fps
→ Read-out modes, Variable partial: Programmable start line: 1 to 760. Programmable height: 8 to 768 lines
→ Read-out modes, Vertical binning: 1024 (h) x 384 (v) 49.3 fps max.
→ Sensitivity: 0.34 Lux (On sensor, max. gain, shutter off, 50% video)
→ S/N ratio: >54dB (Gain 0 dB, shutter off)
→ Video output: Dual monochrome 8, 10, or 12 bit, GigE Vision output Synchronized or separate timing via 2 RJ-45 connectors. Output selectable to one or both channels
→ Auto-iris lens video: 0.7 Vp-p, 75 ohm NUM luminance signal w/o sync
→ Gain: Manual or AGC: -3dB to +21dB
→ Synchronization: Int. X-tal
→ GPIO Module, Input/output switch: Configurable 21-in/14-out switch
→ GPIO Module, Clock generator (one): 12-bit counter based on pixel clock
→ GPIO Module, Pulse generator (four): 20-bit counters with programmable length, start point, stop point, repeat
→ Hardware Trigger modes: Edge Pre-Select, Pulse Width Control, Reset Continuous, PIV, Frame Delay, Sequence
→ Electronic shutter, Programmable exposure: 0.5L (20micro s) to 792L (33.3ms) in 1L steps (42.07micro s)
→ Electronic shutter, Exposure Time Abs: micro sec - user definable. Same range as PE
→ Electronic shutter, GPIO plus Pulse Width: 20 micro s to 2 sec.
→ Electronic shutter, Auto shutter: 1/30 to 1/10,000 sec.
→ Pre-processing functions: Auto gain balancing, blemish compensation, shading correction, knee point/slope, LUT/gamma correction
→ Control interface: Register based, GigE Vision/GenICam compliant.
→ Functions controlled via GigE Vision interface: Shutter, gain, black level, trigger mode, read-out mode, GPIO setup, ROI (GenICam mandatory functions)
→ GigE Vision streaming protocol: Packet size (up to 16020 bytes), delayed (frame) read-out, inter-packet delay
→ Indicators on rear panel: Power/hardware trigger, GigE link/activity
→ Operating Temperature: -5°C to +45°C
→ Humidity (operation): 20 - 80% non-condensing
→ Storage temp./humidity: -25°C to +60°C / 20 to 80%
→ Vibration: 3 G (15Hz to 200 Hz XYZ)
→ Shock: 50G
→ Regulations: CE (EN 61000-6-2, EN-61000-6-3), FCC part 15 class B, RoHS
→ Power: 12V - 24V DC ± 10%. 7.6 W typical (full frame @ 12V)
→ Lens mount: C-mount (use 3CCD type, Max. 4.0 mm thread)
→ Dimensions (H x W x L): 55(H) x 55(W) x 98.3(D) mm
→ Weight: 320 g