JAI CM-030GE-RH 1/3" Monochrome Progressive Scan Camera With Φ 17mm Remote Head

→ 1/3" monochrome progressive scan camera with Φ 17mm remote head
→ Member of C3 Compact series, covering VGA to UXGA resolution
→ 656 (h) x 494 (v) 7.4 μm square pixels
→ 120 frames/second with external trigger and full resolution
→ Increased frame rate with vertical binning and partial scan
→ Exposure time from 32.48 μs to 2 sec. using Pulse Width control
→ Programmable exposure from 32.48 μs to 8.299 ms in Full Frame scan
→ Sequencer trigger mode for on-the-fly change of gain, exposure and ROI
→ LVAL-synchronous/-asynchronous operation (auto-detect)
→ GigE Vision interface with 10 or 8-bit output
→ Programmable GPIO with opto-isolated inputs and outputs
→ Comprehensive JAI SDK & Control Tool for Windows XP/Vista/Windows 7
→ Sensor: 1/3" monochrome progressive scan CCD
→ Pixel Clock: 58 MHz
→ Frame rate full frame: 120 frames/second (511 lines/frame)
→ Active area: 4.9 (h) x 3.7 (v) mm
→ Cell size: 7.4 (h) x 7.4 (v) μm
→ Active pixels: 656 (h) x 494 (v)
→ Read-out modes, Full: 656 (h) x 494 (v) 120.4 fps
→ Read-out modes, 2/3 partial scan: 656 (h) x 328 (v) 172.9 fps
→ Read-out modes, 1/2 partial scan: 656 (h) x 246 (v) 216.8 fps
→ Read-out modes, 1/4 partial scan: 656 (h) x 122 (v) 349.8 fps
→ Read-out modes, 1/8 partial scan: 656 (h) x 60 (v) 504.7 fps
→ Read-out modes, Vertical binning: 656 (h) x 247 (v) 193.8 fps
→ Read-out modes, Region-of-interest (ROI): User definable. Memory read-out
→ Sensitivity: 0.41 Lux (On sensor, max. gain, shutter off, 50% video)
→ S/N ratio: >50dB (0 dB gain)
→ Video output: GigE Vision, 8-bit or 10-bit
→ Gain: Manual -3 to +12 dB
→ Synchronization: Internal X-tal, External hardware trigger via GPIO; Software trigger via GigE Vision
→ GPIO Module, Input/output switch: Configurable 14-in/9-out switch (LUT)
→ GPIO Module, Clock generator (one): 12-bit counter based on 25MHz clock or Pixel Clock
→ GPIO Module, Pulse generators (four): 20-bit counters programmable for length,start point, stop point, repeat
→ Hardware trigger modes: Continuous, Pre-Select, Pulse Width, Frame Delay, Reset Continuous, Sequence (Gain, Shutter, ROI)
→ Electronic shutter, Pre-set shutter: 1/120 to 1/30,000 in 9 steps
→ Electronic shutter, Programmable exposure: 2L (32.48μs) to 511L (8.299ms) in 1L steps
→ Electronic shutter, Exposure Time (Abs): Same range as PE
→ Electronic shutter, Pulse Width: 2L to 24o frames (32.48μs to 2 seconds)
→ GPIO plus Pulse Width: Register based, GigE Vision (GenICam compliant)
→ Functions controlled via GigE Vision interface: Shutter, Gain, Black level, Trigger mode, Readout mode, GPIO setup, ROI (GenICam mandatory functions)
→ GigE Vision streaming control: Packet size, Delayed (frame) Readout, Inter-packet delay
→ Indicators on rear panel Power / Hardware trigger, GigE link, GigE activity
→ Operating Temperature: -5°C to +45°C
→ Humidity (operation): 20 - 90% non-condensing
→ Storage temp./humidity: -25°C to +60°C / 20 to 90% non-condensing
→ Vibration: 10 G (20Hz to 200 Hz XYZ)
→ Shock: 70G
→ Regulations: CE (EN 61000-6-2, EN-61000-6-3), FCC part 15 class B, RoHS/WEEE
→ Power: 12V DC +/-10%. 3.6 W
→ Lens mount: phi17mm exclusive mount
→ Dimensions: (H x W x L) 29 x 44 x 75 mm (ccu)
→ Weight: 130 g + 120g (head with 2m cable)