JAI CM-040GE 1/2" Monochrome Progressive Scan 0.4 MP Camera

→ 1/2" monochrome progressive scan camera
→ Member of C3 Compact series, covering VGA to UXGA resolution
→ 782 (h) x 582 (v) 8.37 micro m square pixels
→ 61.15 frames/second with full resolution in continuous operation
→ Increased frame rate with vertical binning (CM-040 GE) and partial scan
→ Exposure time from 54.874 micro s to 2 sec. using Pulse Width trigger mode
→ Programmable exposure from 54,874 micro s to 16.353ms in Full Frame scan
→ Sequence trigger mode for on-the-fly change of gain, exposure and ROI
→ LVAL Synchronous/-asynchronous operation (auto-detect)
→ Auto iris lens video output allows a wider range of light
→ GigE Vision interface with 10 or 8-bit output
→ Partial scan and vertical binning
→ Unique sequencer function
→ Programmable GPIO with opto-isolated inputs and outputs
→ Comprehensive software tools and SDK for Windows XP/Vista
→ Sensor: 1/2" progressive scan CCD
→ Pixel Clock: 33.75 MHz
→ Frame rate full frame: 61.15 frames/second
→ Active area: 6.49 (h) x 4.83 (v) mm
→ Cell size: 8.3 (h) x 8.3 (v) micro m
→ Active pixels: 776 (h) x 582 (v)
→ Read-out modes, Full: 776 (h) x 582 (v) 61 fps
→ Read-out modes, 1/2 partial scan: 776 (h) x 294 (v) 110 fps
→ Read-out modes, 1/4 partial scan: 776 (h) x 146 (v) 186 fps
→ Read-out modes, 1/8 partial scan: 776 (h) x 74 (v) 280 fps
→ Read-out modes, 2/3 partial scan: 776 (h) x 390 (v) 87 fps
→ Read-out modes, Vertical binning: (CM-040 GE only) 776 (h) x 291 (v) 111 fps
→ Read-out modes, Region-of-interest (ROI): User Definable. Memory read-out
→ Sensitivity: (CM-040 GE) 0.2 Lux (On sensor, max. gain, shutter off, 50% video)
→ S/N ratio: >50 dB(0 dB gain)
→ Video output: GigE Vision, 8-bit or 10-bit
→ Auto-iris lens video output: 0.7 Vp-p, enabled by internal switch
→ Gain: Manual -3dB to 24 dB
→ Synchronization: Internal X-tal, External hardware trigger via GPIO; Software trigger via GigE Vision
→ GPIO Module, Input/output switch: Configurable 14-in/9-out switch (LUT)
→ GPIO Module, Clock generator (one): 12-bit counter based on 25MHz clock or Pixel Clock
→ GPIO Module, Pulse generators (four): 20-bit counters programmable for length, start point, end point, repeat
→ Hardware trigger modes: Continuous, Pre-Select, Pulse Width, Frame delay, Sequence (Gain, Shutter, ROI)
→ Electronic shutter, Pre-set shutter: 1/60 to 1/10,000 in 10 steps
→ Electronic shutter, Programmable exposure: 2L(54.874 micro s ) to 596L (16.353ms) in 1L steps
→ Electronic shutter, Exposure Time (Abs): micro sec – user definable. Same range as PE
→ Electronic shutter, Pulse Width: max. 2 sec. (can be set by 100 micro s unit or Pixel Clock unit)
→ Control interface: Register based GigE Vision/GenICam compliant
→ Functions controlled via GigE Vision interface: Shutter, Gain, Black level, Trigger mode, Readout mode, GPIO setup, ROI (GenICam mandatory functions)
→ GigE Vision streaming control: Packet size (1428 to 4040bytes), Delayed (frame) readout, Inter-packet delay,
→ Indicators on rear panel: Power / Hardware trigger, GigE link, GigE activity
→ Operating Temperature: -5°C to 45°C
→ Humidity (operation): 20 - 80% non-condensing
→ Storage temp./humidity: -25°C to 60°C / 20 to 80%
→ Vibration: 10G (20Hz to 200 Hz XYZ)
→ Shock: 70G
→ Regulations: CE (EN 61000-6-2, EN-61000-6-3), FCC part 15 class B, RoHS/WEEE
→ Power: 12V DC /-10%. 3.6W
→ Lens: mount C-mount
→ Dimensions: (H x W x L) 29 x 44 x 75 mm
→ Weight: 125 g