JAI CM-140GE 1/2" Monochrome Progressive Scan 1.4 MP Camera

→ 1/2" monochrome progressive scan camera
→ Member of C3 Compact series, covering VGA to UXGA resolution
→ 1392 (h) x 1040 (v) 4.65 micro m square pixels
→ 31 frames/second with full resolution in continuous operation
→ 30 frames/second with external trigger and full resolution
→ Increased frame rate with vertical binning (CM-140 GE) and partial scan
→ Exposure time from 31 micro s to 2 sec. using Pulse Width trigger mode
→ Programmable exposure from 61.2 micro s to 32.2 ms
→ Sequencer trigger mode for on-the-fly change of gain, exposure and ROI
→ LVAL-synchronous/-asynchronous operation (auto-detect)
→ Auto iris lens video output allows a wider range of light
→ GigE Vision interface with 10 or 8-bit output
→ Partial scan
→ Unique sequencer function
→ Programmable GPIO with opto-isolated inputs and outputs
→ Comprehensive software tools and SDK for Windows XP/Vista
→ Sensor: 1/2" progressive scan
→ Pixel Clock: 65 MHz
→ Frame rate full frame: 31.08 frames/second (1052 lines per frame)
→ Active area: 6.4 (h) x 4.8 (v) mm
→ Cell size: 4.65 x 4.65 pixels
→ Active pixels: 1392 x 1040
→ Read-out modes, Full: 1392 (h) x 1040 (v) 31.08 fps
→ Read-out modes, 1/2 partial scan: 1392 (h) x 520(v) 46.57 fps
→ Read-out modes, 1/4 partial scan: 1392 (h) x 260 (v) 61.92 fps
→ Read-out modes, 1/8 partial scan: 1392 (h) x 130 (v) 73.97 fps
→ Read-out modes, 2/3 partial scan: 1392 (h) x 694 (v) 39.97 fps
→ Read-out modes, Vertical binning: 1392 (h) x 520 (v) 48.86 fps**NOTE: CM-140 GE only
→ Read-out modes, Region-of-interest (ROI): User definable. Memory read-out
→ Sensitivity: (CM-140 GE) 0.3 Lux (On sensor, max. gain, shutter off, 50% video)
→ S/N ratio: >50dB (0dB gain)
→ Video output: GigE Vision, 8-bit or 10-bit
→ Auto-iris lens video output: 0.7 Vp-p, enabled by internal switch
→ Gain: Manual, -3 to +24 dB
→ Synchronization: External hardware trigger via GPIO; Software trigger via GigE Vision
→ GPIO Module, Input/output switch: Configurable 14-in/9-out switch (LUT)
→ GPIO Module, Clock generator (one): 12-bit counter based on 25MHz clock or Pixel Clock
→ GPIO Module, Pulse generators (four): 20-bit counters programmable for length, start point, stop point, repeat
→ Hardware trigger modes: Continuous, Pre-Select, Pulse Width, Sequence (Gain, Shutter, ROI) Reset-continous trigger, Delay Readout
→ Electronic shutter, Pre-set shutter: 1/31 to 1/10,000 in 10 steps
→ Electronic shutter, Programmable exposure: 2L (61.2 micro s) to 1052L (32.2ms) in 1L steps
→ Electronic shutter, Exposure Time (Abs): micro sec - user definable. Same range as PE
→ Electronic shutter, Pulse Width: 31 micro s to 2 sec.
→ Control interface: Register based. GigE Vision/GenICam compliant
→ Functions controlled via GigE Vision interface: Shutter, Gain, Black level, Trigger mode, Readout mode, GPIO setup, ROI (GenICam mandatory functions)
→ GigE Vision streaming control: Packet size (1428 to 4040 bytes), Delayed (frame) Readout, Inter-packet delay
→ Indicators on rear panel: Power / Hardware trigger, GigE link, GigE activity
→ Operating Temperature: -5°C to +45°C
→ Humidity (operation): 20 - 90% non-condensing
→ Storage temp./humidity: -25°C to +60°C / 20 to 90%
→ Vibration: 10G (20Hz to 200 Hz XYZ)
→ Shock: 70G
→ Regulations: CE (EN 61000-6-2, EN-61000-6-3), FCC part 15 class B, RoHS/WEEE
→ Power: 12V DC +/-10%. 3.5W
→ Lens mount: C-mount
→ Dimensions: (H x W x L) 29 x 44 x 75 mm
→ Weight: 125 g