JAI CV-A10GE 1/2" Monochrome Progressive Scan Camera, GigE Vision

→ 1/2" progressive scan camera
→ Monochrome and Bayer color versions
→ 782 (h) x 582 (v) 8.37μm square pixels
→ 60 fps with full resolution
→ 250 fps with 1/8 partial scan
→ Vertical binning for higher frame rates and sensitivity
→ High speed shutter from 1/60 to 1/300,000 second
→ 8 or 10-bit output
→ Edge pre-select, and pulse width trigger modes
→ Sequencer trigger mode for on-the-fly change of shutter, and gain
→ Auto exposure and smearless mode
→ Auto-Iris lens video output, auto shutter and AGC allow a wider light range
→ Programmable GPIO
→ Comprehensive software suite and SDK for Windows XP
→ Sensor: 1/2" progressive scan IT CCD
→ Pixel clock: 36.15 MHz
→ Frame rate full frame: 60 frames/sec. (1125 lines/frame)
→ Active area: 6.4 (h) x 4.8 (v) mm
→ Cell size: 8.3 (h) x 8.3 (v) μm
→ Active pixels: 767 (h) x 576 (v)
→ Color (CV-A70 GE): Raw Bayer output host-based interpolation
→ Read-out modes, Full: 767 (h) x 576 (v) 60 fps
→ Read-out modes, 1/2 partial scan: 767 (h) x 287 (v) 112 fps
→ Read-out modes, 1/3 partial scan: 767 (h) x 143 (v) 177 fps
→ Read-out modes, 1/4 partial scan: 767 (h) x 71 (v) 250 fps
→ Read-out modes, 2x Vert. binning (CV-A10 GE only): 767 (h) x 287 (v) 107 fps
→ Read-out modes, 3x Vert. binning (CV-A10 GE only): 767 (h) x 191 (v) 144 fps
→ Read-out modes, 4x Vert. binning (CV-A10 GE only): 767 (h) x 143 (v) 174 fps
→ Read-out modes, Region-of-interest(ROI): User definable. Memory read-out
→ Sensitivity (CV-A10 GE): 0.1 Lux (On sensor Max. gain, shutter off,50% video)
→ S/N ratio: >55 dB (Gain 0 dB, shutter off)
→ Video output: GigE Vision, 8 or 10 bits
→ Auto-iris lens video output: 0.7 Vpp
→ Gain: Manual/Automatic
→ Gain: Range. -3 to +12 dB
→ Synchronization External hardware trigger via GPIO; Software trigger via GigE Vision
→ GPIO Module, Input / output switch: Configurable 12-in / 9-out switch (LUT)
→ GPIO Module, Clock generator (one): 12-bit counter (based on 25MHz clock or pixel clock)
→ GPIO Module, Pulse generators (four): 20-bit counters programmable for Length, start point, stop point, repeat
→ Hardware trigger modes: Continuous, Edge Pre-select (EPS), Pulse Width Control (PWC), Sequence (Gain, shutter)
→ Electronic shutter, Preset shutter: 1/60 to 1/300,000 sec. in 14 steps
→ Electronic shutter, Programmable exposure: 1/8 line to 628 lines (3.3μs to 16.7ms)
→ Electronic shutter, Auto exposure: 1/60 to 1/25,000 second (cont. mode only)
→ Electronic shutter, Exposure time (Abs): μsec - user definable. Same range as PE
→ Electronic shutter, Pulse width control: 66.7μs to 2 sec.
→ Control interface: Register based GigE Vision (GenICam compliant)
→ Functions controlled via GigE Vision interface: Shutter, Trigger mode, Readout mode, GPIO setup, ROI ,Gain, Black level (GenICam mandatory functions)
→ GigE Vision streaming control: Packet size, Delayed (frame) Readout, Inter-packet delay
→ Indicators on rear panel: Power / Hardware trigger, GigE link, GigE activity
→ Operating temperature: -10°C to +45°C
→ Humidity: 20 – 90% non-condensing
→ Storage temp./humidity: -25°C to +60°C/20% to 90%
→ Vibration: 10G (20Hz to 200Hz XYZ)
→ Shock: 70G
→ Regulations: CE (EN61000-6-2 and EN61000-6-3), FCC part 15 class B RoHS / WEEE
→ Power: 12V DC ± 10%. 5.5 W
→ Lens mount: C-mount
→ Dimensions: (H x W x L) 55 x 55 x 55 mm
→ Weight: 220 g