NVT NV-4PS13-PVD 4-Channel Power Supply Passive Receiver Hub
Offering Wholesale, OEM, USA / International, GSA Government / Educational, Reseller / Retail, & Quantity Prices and Specifications / Datasheets, Installation Guides, and Operational Manuals.
Price Documents
→ Video Attenuation 0.5 dB typ
→ Video Common-mode / Differential-mode rejection: 15 KHz to 5 MHz 60 dB typ
→ Video Impedance Coax, female BNC: 75 ohms
→ Video Impedance UTP, RJ45: 100 ohms
→ Video Network Wiring: One four-pair Cat5 or better per channel
→ Camera Power: Fully isolated (floating) Class 2 SELV output, individually switchable 24VAC/OFF/28VAC at up to 1 Amp.
→ Each output is individually thermistor protected
→ Power inlet: IEC with molded power cord (included)
→ Power On-off switch: Rear panel
→ Power Voltage: 115 / 230 VAC
→ Power Current: 1.25 / 0.625 Amps
→ Power Frequency: 50 / 60 Hz
→ Power Protection: 2.5A slo-blo 8x20mm fuse and thermal shutdown
→ Power Wattage: 125 Watts
→ Power Heat: (power supply only) 50 BTU/hour (power supply with cameras) 420 BTU/hour
→ Blue LED: System power on
→ Per-channel LED indicates Off: No load connected
→ Per-channel LED indicates Green: Load connected and working
→ Per-channel LED indicates Amber: Mis-wiring detected
→ Per-channel LED indicates Red: Overload shutdown condition
→ Ambient Temperature: -4 to 122 °F (-20 to 50 °C)
→ Humidity (non-condensing): 0 to 95%
→ Transient Immunity: per ANSI 587 C62.41
→ Dimensions: 9.25in wide, 1.75in high, 7.25in deep
→ Including connectors: (235mm wide, 44,5mm high, 184mm deep)
→ Mounting: Wall, or desk mount
→ Product Weight: 7lb (3,2kg)
→ Packaged Weight: 8.42lb (3,8kg)
→ Provides Class 2 SELV camera power while receiving video transmission and delivering P/T/Z telemetry all over a single 4-pair Cat5e cable
→ Standard telecom/datacom structured cabling pinouts per EIA/TIA 568B
→ Independently selectable 24VAC-OFF-28VAC with 1 Amp per channel
→ Automatic-reset fault protection; transient protection
→ Frequency Response DC to 10 MHz
→ Individually floating outputs ensure total ground-loop immunity
→ Diagnostic LEDs show load/no load, miswires, and overload conditions
→ Use with the NV-216A-PV, NV-218A-PVD or the NV-226J-PV transceiver at the camera
→ Power cameras via UTP over significant distances (see Power Distance Calculator)
→ 1U high x 8" deep wall, desk or desk rack-mountable
→ Limited lifetime warranty
The NVT 4 Channel Power Supply Passive Receiver Hub NV 4PS13 PVD is a key hybrid component that consolidates all CCTV system cabling using standard EIA/TIA 568B structured building wiring. Designed for installation in the IDF/Telecom Closet or MDF/Equipment Room, the Power Supply Passive Video Receiver Hub has independently selectable 24VAC-OFF-28VAC outputs that can support at-distance camera loads up to 1 Amp per channel. Use with NVTs PVD transceivers for cable runs under 750ft (225m) .
The NV4PS13PVD has a built-in passive receiver hub that allows connection to DVR or an encoder for IP transmission. Per-channel diagnostic LEDs display load /no-load, miswires, or fault conditions at a glance. Automatic-reset fault protection, transient protection, and ground loop free individually floating outputs.
Similar Models:
NV-8PS13-PVD: 8 Channel Power Supply Passive Receiver Hub
NV-16PS13-PVD: 16 Channel Power Supply Passive Receiver Hub
