Search

2/3" Interline Progressive CCD Color Camera

Sentech - STC-GEC500A View Larger Image (in new window)

Sentech : STC-GEC500A

Contact us for lowest price (800) 284-2288 , (858) 565-1101 Call Now [email protected]
The Sentech STCGEC500A is part of Sentech's Standard GigE camera line. It features a 2/3" color QSXGA sensor, 15fps and communication over a 6 pin Hirose or Ethernet connector.

The STC GEC500A boasts precision housing with accurate CCD alignment, a DC Auto Iris Lens Driver, a user-programmable Area of Interest (AOI) and a Gamma Table that can be imported. This camera meets all industry standards for GigE Vision� and GenICam�.

2/3" CCD Image Sensor
QSXGA (5 Megapixel), 15fps
User-Programmable Area of Interest (AOI)
Imager 2/3” Interline QSXGA color progressive CCD: ICX625AQ
Total Picture Element 2536 (H) x 2068 (V)
Active Picture Element QSXGA: 2448 (H) x 2058 (V)
Chip Size 9.93 (H) x 8.70 (V) mm
Cell Size 3.45 (H) x 3.45 (V) µm
Scanning System Progressive
Vertical Frequency (Frame Rate) 15 Hz at full resolution 0.48175 to 60.71422 Hz adjustable via the communication Max. frame rate depends on the AOI setting Max. frame rate of the camera(60.71422 Hz) is 128 vertical resolution AOI setting
Horizontal Frequency 31.1284 kHz
Pixel Frequency 31.1284 MHz
Noise Level - @ 8bit output ≤ 4 Digit (Gain 0 dB)
Noise Level - @ 10bit output ≤ 15 Digit (Gain 0 dB)
Noise Level - @ 12bit output ≤ 60 Digit (Gain 0 dB)
Minimum Scene Illumination 6.48 Lux at F1.2, 15 Hz
Sync System Internal
Video Output Digital 8, 10 or 12 bit Raw Data or RGB 8 bit
Interface IEEE802.3 (1000BASE-T)
Protocol GigE Vision® 1.2 and GenICam™ 2.0 compliant
Exposure Time Preset continuous mode: 10 useconds to 16,777,216 useconds Preset trigger mode: 10 useconds to 16,777,216 useconds Pulse width mode: 10 useconds to Unlimited
ALC Auto iris lens, electronic iris and AGC (ON / OFF)
Gain 0 to 20.4 dB
Gamma Gamma 1.0 (Factory default) or uploadable gamma table
AOI Function Programmable AOI setting via the communication
Smear Reduction Selectable ON / OFF via the communication
Color Interpolation Available on RGB output
White Balance Function Auto, manual and push-to-set white balance is available on both Raw data output and RGB output
Trigger Mode Edge preset trigger, Pulse width trigger (unlimited long exposure)
Communication UART Communication through Ethernet port
I/Os One opto-isolated input and two LVTTL outputs
Auto IRIS lens control DC IRIS control input with video level target, peak/average and zone weight settings via the communication
Power - Input Voltage 10.8 to 26.4 Vdc
Power - Consumption < 6.0 W
Dimensions 35 (W) x 35 (H) x 50.6 (D) mm excluding connectors
Optical Filter IR cut filter on
Optical Center Accuracy Positional accuracy in H and V directions: /0.3 mm Rotational accuracy of H and V: /1.5 deg.
Material Aluminum (AC)
Lens Mount C mount
Connectors RJ45 connector Power/IO connector: HR10A-7R-6PB (Hirose) or equivalent DC IRIS lens connector: M1951 (EMUDEN) or equivalent
Camera Mount Screws Two 1/4” Tripod screw holes: (One on each top and bottom plate), Twelve M4 screws holes: (Four on each top and bottom plate, two on each side plate)
Weight Approximately 120g
Operating Temperature - Minimum Environmental temperature -5 deg. C
Operating Temperature - Maximum TBD
Storage Temperature Environmental temperature -30 ~ 65 deg. C
Vibration 20 Hz to 200 Hz to 20 Hz (5 min. /cycle), acceleration 10G, 3 directions 30 min. each
Shock Acceleration 38G, half amplitude 6 ms, 3 directions 3 times each
Standard Compliancy EMS: EN61000-6-2, EMI: EN55011
RoHS RoHS Compliant



facebook.png twitter.png googleplus.png linkedin.png youtube.png
Prices and specifications subject to change without notice.