1/2" Interline Progressive CCD SXGA 19 fps 1360 x 1040 Monochrome Camera

The STCPOGE152A is part of Sentech's Power Over Ethernet GigE camera line. It features a 1/2" monochrome SXGA sensor, 19fps and communication over a 12 pin Hirose or Ethernet connector.

The STC POGE152A boasts precision housing with accurate CCD alignment, a DC Auto Iris Lens Driver, a user-programmable Area of Interest (AOI) and a Gamma Table that can be imported. This camera meets all industry standards for GigE Vision� and GenICam�.

→ 1/2" CCD Image Sensor
→ SXGA (1.3 Megapixel), 19fps
→ PoE (Power Over Ethernet)

Imager	1/2" Interline SXGA monochrome progressive CCD: ICX205AL
Total Picture Element	1434 (H) x 1050 (V)
Active Picture Element	SXGA: 1360 (H) x 1040 (V)
Chip Size	7.6 (H) x 6.2 (V) mm
Cell Size	4.65 (H) x 4.65 (V) µm
Scanning System	Progressive
Vertical Frequency (Frame Rate)	19.25954 Hz at full resolution 0.31387 to 71.66965 Hz adjustable via the communication Max. frame rate depends on the AOI setting Max. frame rate of the camera(71.66965) is 200 vertical resolution AOI setting
Horizontal Frequency	20.5688 kHz
Pixel Frequency	36.818175 MHz
Noise Level - @ 8bit output	≤ 3 Digit (Gain 0 dB)
Noise Level - @ 10bit output	≤ 12 Digit (Gain 0 dB)
Noise Level - @ 12bit output	≤ 48 Digit (Gain 0 dB)
Minimum Scene Illumination	0.41 Lux at F1.2, 19.25954 Hz
Sync System	Internal
Video Output	Digital 8, 10 or 12 bit Raw Data
Interface	PoE: IEEE802.3af (1000BASE-T)
Protocol	GigE Vision® 1.2 and GenICam™ 2.0 compliant
Shutter Speed	Preset continuous mode: 10 useconds to 17,666,216 useconds Preset trigger mode: 10 useconds to 17,666,216 useconds Pulse width mode: 10 useconds to Unlimited
ALC	Auto iris lens, electronic iris and AGC (ON / OFF)
Gain	0 to 20.4 dB
Gamma	Gamma 1.0 (Factory default) or downloadable gamma table
AOI Function	Programmable AOI setting via the communication
Smear Reduction	Selectable ON / OFF via the communication
Trigger Mode	Edge preset trigger, Pulse width trigger (unlimited long exposure)
Communication	UART communication through Ethernet port
I/Os	3 opto-isolated inputs and 5 opto-isolated outputs
Auto IRIS lens control	DC IRIS control input with video level target, peak/average and zone weight settings via the communication
Power - Input Voltage	10.8 to 26.4 Vdc through power/IO connector or Power Over Ethernet (Auto detection with power/IO connector prioritized)
Power - Consumption	< 4.5 W
Dimensions	50 (W) x 50 (H) x 53.5 (D) mm excluding connectors
Optical Filter	No filter
Optical Center Accuracy	Positional accuracy in H and V directions: /0.3 mm Rotational accuracy of H and V: /1.5 deg.
Material	Aluminum (AC)
Lens Mount	C mount
Connectors	RJ45 connector Power/IO connector: HR10A-10R-12PB (Hirose) or equivalent DC IRIS lens connector: M1951 (EMUDEN) or equivalent
Camera Mount Screws	Two 1/4” Tripod screw holes: (One on each top and bottom plate), Sixteen M4 screws holes: (Four on each top, bottom and both side plates)
Weight	Approximately 170g
Operating Temperature	-5 ~ 40 deg. C
Storage Temperature	-30 ~ 65 deg. C
Vibration	20 Hz to 200 Hz to 20 Hz (5 min. /cycle), acceleration 10G, 3 directions 30 min. each
Shock	Acceleration 38G, half amplitude 6 ms, 3 directions 3 times each
Standard Compliancy	TBD
RoHS	RoHS Compliant