Search

1/1.8" Interline Progressive CCD UXGA 315 fps 1624 x 1236 Color Camera

Sentech - STC-POGEC202A View Larger Image (in new window)

Sentech : STC-POGEC202A

Contact us for lowest price (800) 284-2288 , (858) 565-1101 Call Now [email protected]
The STCPOGEC202A is part of Sentech's Power Over Ethernet GigE camera line. It features a 1/1.8" color UXGA sensor, 15fps and communication over a 12 pin Hirose or Ethernet connector.

The STC POGEC202A boasts precision housing with accurate CCD alignment, a DC Auto Iris Lens Driver, a user-programmable Area of Interest (AOI) and a Gamma Table that can be imported. This camera meets all industry standards for GigE Vision� and GenICam�.

1/1.8" CCD Image Sensor
UXGA (2 Megapixel), 15fps
PoE (Power Over Ethernet)
Imager 1/1.8” Interline UXGA color progressive CCD: ICX274AQ
Total Picture Element 1688 (H) x 1246 (V)
Active Picture Element UXGA: 1624 (H) x 1236 (V)
Chip Size 8.5 (H) x 6.8 (V) mm
Cell Size 4.4 (H) x 4.4 (V) µm
Scanning System Progressive
Vertical Frequency (Frame Rate) 15.31668 Hz at full resolution 0.29261 to 61.26674 Hz adjustable via the communication Maximum frame rate depends on the AOI setting Maximum frame rate of the camera(61.26674) is 230 vertical resolution AOI setting
Horizontal Frequency 19.1761 kHz
Pixel Frequency 36.8181 MHz
Noise Level - @ 8bit output ≤ 3 Digit (Gain 0 dB)
Noise Level - @ 10bit output ≤ 12 Digit (Gain 0 dB)
Noise Level - @ 12bit output ≤ 48 Digit (Gain 0 dB)
Minimum Scene Illumination 7.27 Lux at F1.2, 15.31668 Hz
Sync System Internal
Video Output Digital 8, 10 or 12 bit Raw Data or RGB 8 bit
Interface PoE: IEEE802.3af CLASS3 (1000BASE-T)
Protocol GigE Vision® 1.2 and GenICam™ 2.0 compliant
Shutter Speed Preset continuous mode: 10 useconds to 16,777,216 useconds Preset trigger mode: 10 useconds to 16,777,216 useconds Pulse width mode: 10 useconds to Unlimited
ALC Auto iris lens, electronic iris and AGC (ON/OFF)
Gain 0 to 20.4 dB
Gamma Gamma 1.0 (Factory default) or uploadable gamma table
AOI Function Programmable AOI setting via the communication
Smear Reduction Selectable ON/OFF via the communication
Color Interpolation Available on RGB output
White Balance Function Auto, manual and push-to-set white balance is available on both Raw data output and RGB output
Trigger Mode Edge preset trigger, Pulse width trigger (unlimited long exposure)
Communication UART Communication through Ethernet port
I/Os 3 opto-isolated inputs and 5 opto-isolated outputs
Auto IRIS lens control DC IRIS control input with video level target, peak/average and zone weight settings via the communication
Power - Input Voltage 10.8 to 26.4 Vdc through power/IO connector or Power Over Ethernet (Auto detection with power/IO connector prioritized)
Power - Consumption Less than 5.0 W
Dimensions 50 (W) x 50 (H) x 53.5 (D) mm excluding connectors
Optical Filter IR cut filter on
Optical Center Accuracy Positional accuracy in H and V directions: /0.3 mm Rotational accuracy of H and V: /1.5 deg.
Material Aluminum (AC)
Lens Mount C mount
Connectors RJ45 connector Power/IO connector: HR10A-10R-12PB (Hirose) or equivalent DC IRIS lens connector: M1951 (EMUDEN) or equivalent
Camera Mount Screws Two 1/4” Tripod screw holes: (One on each top and bottom plate), Sixteen M4 screws holes: (Four on each top, bottom and both side plate)
Weight Approximately 170 g
Operating Temperature -5 ~ 40 deg C
Storage Temperature -30 ~ 65 deg C
Vibration 20Hz to 200Hz to 20Hz (5min./cycle), acceleration 10G, 3 directions 30 min. each
Shock Acceleration 38G, half amplitude 6ms, 3 directions 3 times each
Standard Compliancy TBD
RoHS RoHS Compliant



facebook.png twitter.png googleplus.png linkedin.png youtube.png
Prices and specifications subject to change without notice.