1/1.8" UXGA (1600 x 1200), 30 fps, 2.0MP, Color GigE camera, w/ IR cut filter, w/ POE

• User Programmable AOI

• High Speed Power Over Ethernet

• 2.0 Megapixel Resolution with 30 fps

Imager

1/1.8” interline UXGA color progressive CCD: ICX274AQ

Total Picture Element

1688 (H) x 1246 (V)

Active Picture Element

UXGA: 1624 (H) x 1236 (V)

Chip Size

8.5 (H) x 6.8 (V) mm

Cell Size

4.4 (H) x 4.4 (V) um

Scanning System

Progressive

Vertical Frequency

30.29207 Hz at full resolution; 0.57871 to 121.16830Hz changeable via the communication; Maximum frame rate is dependent on the AOI setting; Maximum frame rate of the camera (121.16830 Hz) is 104 vertical resolution AOI setting.

Horizontal Frequency

37.9257 Hz

Pixel Frequency

72.81683 MHz

Noise Level

-

- @ 8Bit Output

<= 3 Digit (Gain 0 dB)

- @ 10Bit Output

<= 12 Digit (Gain 0 dB)

- @ 12Bit Output

<= 48 Digit (gain 0 dB)

Minimum Scene Illumination

7.27 Lux at F1.2, 15.31668 Hz

Sync System

Internal

Video Output

Digital 8 ,10 or 12 bit Raw Data or RGB 8 bit

Interface

PoE: IEEE802.3af CLASS3 (1000BASE-T)

Protocol

GigE Vision 1.2 and GeniCam 2.0 compliant

Exposure Time

Preset continuous mode: 10 seconds to 16,777,216 seconds; Preset trigger mode: 10 seconds to 16,777,216 seconds; Pulse width mode: 10 seconds to Unlimited.

ALC

Electronic iris and AGC (ON/OFF)

Gain

0 to 20.4 dB

Gamma

Gamma 1.0 (Factory default) or downloadable gamma table

AOI (Area of Interest) Function

Programmable AOI setting via the communication

Smear Reduction

Selectable ON/OFF via the communication

Color Interpolation

Available on RGB output

White Balance

Auto, Manual, and push to set white balance is available on both Raw Data output and RGB output.

Trigger Mode

Edge preset trigger, pulse width trigger (unlimited exposure time)

Communication

UART communication through Ethernet Port

I/Os

One opt isolated input and two open collector outputs

Power

-

- Input Voltage

+10.8 to +26.4Vdc through power/IO connector or Power Over Ethernet; (Auto detection with power/IO connector prioritized)

- Consumption

12V: 4.1W / 3.9W, PoE: 4.4W / 4.2W

Dimensions

35 (W) x 35 (H) x 57.3 (D) mm excluding connectors

Optical Filter

IR cut filter on

Optical Center Accuracy

Positional accuracy in H and V directions: +/- 0.3 mm; Rotational accuracy of H and V: +/- 1.5 deg.

Material

Aluminum (AC)

Lens Mount

C Mount

Connectors

RJ45 connector; Power/IO connector: HR10A-10R-6PB (Hirose) or equivalent

Camera Mount Screws

Two ¼” Tripod screw holes (one each on top and bottom plate); Twelve M4 screw holes (four each on top, bottom, and two each on both side plates)

Weight

Approx. 130

Operating Temperature

- Minimum

Environmental Temperature: -5 deg. C

- Maximum

Camera housing temperature (top plate) shall not exceed 65 deg. C (This corresponds to an environmental temperature of approximately 35 deg. C)

Storage Temperature

Environmental Temperature: -30 to 65 deg. C

Vibration

20Hz to 200Hz to 20Hz (5min/cycle), acceleration 10G, 3 directions 30 min. each

Shock

Acceleration 38G, half amplitude 6ms, 3 directions, 3 times each

Standard Compliancy

EMS: EN61000-6-2, EMI: EN55011

RoHS

RoHS compliant