EthernetConnect Switch: 4-Port, self-managed, PoE+ switch with Extended Uplink

The EthernetConnect™ EC-4BY1SWC/U Series has two models that provide different front panel connectors; the C model for coaxial applications and the U model for UTP applications.

The EthernetConnect EC-4BY1SWC/U Series is an Ethernet switch with uplink management functionality that operates on the Ethernet over copper (EoC). It provides four ports operating at 10/100 Mbps and is designed to combine these four electrical ports into a single electrical extended port that forwards the data to the next network device. The switch does not require programming prior to use.

The EC-4BY1SWC/U Series comes pre-programmed, preventing network video flooding with DIP switch selection of the extended distance port as uplink. Ports 1 through 4 can supply up to 30 W of Power over Ethernet (PoE) and incorporate PoE+ features based on the IEEE802.3at standard. Front panel LED indicators confirm the operating status of the Ethernet switch.

The EC-4BY1SWC/U Series can be either wall-mounted or chassis-mounted for rack installation. All application configurations should be verified at time of ordering to facilitate ease of installation.

Available Models

EC-4BY1SWCPOE-W EthernetConnect 4-port coaxial self-managed PoE switch, 30 W per port, EoC using coaxial cable, extended uplink, wall mount

EC-4BY1SWUPOE-W EthernetConnect 4-port UTP self-managed PoE switch, 30 W per port, EoC using Cat5/ Cat5e/Cat6 UTP, extended uplink, wall mount

No Programming Required

10/100 Mbps Ethernet – 4 x 10/100BASE-T/TX Electrical Ports Supporting PoE+ – 1 x 100 Mbps Extended Electrical Uplink

Transmits Four Individual Ethernet Data Channels Over Standard Cat5/Cat5e/Cat6 UTP Cable or Over Coaxial Cable

Extends Ethernet up to 914 m (3,000 ft) at 10 Mbps or 610 m (2,000 ft) at 100 Mbps Over Cat5/Cat5e/Cat6 UTP Cable

Extends Ethernet up to 1,524 m (5,000 ft) at 10 Mbps or 610 m (2,000 ft) at 100 Mbps Over Coaxial Cable

Extended Temperature Operation of –40°C to 75°C (–40° to 167°F)

30 W PoE Capability on Ethernet Ports

Electrical Ports Support Autonegotiation for 10 Mbps or 100 Mbps, Full-Duplex or Half-Duplex Data

Pre-Programmed Port for Uplink

Full 10/100 Mbps Bandwidth

Supports Multicast and Unicast

Automatic MDI/MDI-X Crossover

Designed to Meet Full Compliance with the Environmental Requirements (Ambient Operating Temperature, Mechanical Shock, Vibration, Humidity with Condensation, High-Line/Low-Line Voltage Conditions and Transient Voltage Protection) of NEMA TS-1/TS-2 and the Caltrans Specification for Traffic Signal Control Equipment

Voltage Transient Protection on all Power and Signal Input/Output Lines Provides Protection from Power Surges and Other Voltage Transient Events

Power and Activity Status LED Indicators

Hot-Swappable Rack Modules

Interchangeable Between Stand-Alone or Rack Mount Use

IEEE802.3at Compliant

Designed and Manufactured in the USA

ELECTRICAL

Operating Voltage

Non PoE 12 VDC (9 VDC† when in USRACK or EURACK)

PoE 48 VDC

Power Consumption 10 W; PSE source power up to 120 W

Current Protection Automatic resettable solid-state current limiters

MTBF >100,000 hours

LED Indicators Data Link/Data Activity; Power; Power over Ethernet (PoE+)

DATA

Data Interface Ethernet

Data Rate 10/100 Mbps; IEEE802.3 compliant; Ethernet ports: Full/half-duplex; Uplink port: Full-duplex

Standards

• POE+ IEEE802.3af/at
• RFC 768 UDP, 2068 HTTP, 793 TCP, 791 IP, 1783 TFTP, 894 IP over Ethernet

 *Distance figures are obtained using in-house testing mirroring installations. Factors such as coaxial and copper cable quality, the number of connectors and splices in the cable run, the use of PoE, and environmental conditions encountered within the installation might affect the actual transmission distance and should be taken into consideration.

GENERAL

Dimensions 15.5 x 13.5 x 2.8 cm (6.1" D x 5.3" W x 1.1" H)

Operating Temperature –40° to 75°C (–40° to 167°F)

Storage Temperature –40° to 80°C (–40° to 176°F)

Relative Humidity 0% to 95%, noncondensing

Unit Weight <0.45 kg (1 lb) Shipping Weight <0.9 kg (2 lb)

MECHANICAL

Connectors

Power Terminal block

Coaxial Female BNC

UTP RJ-45

Data RJ-45

Surface Mount Wall or flat surface screw attachment

CERTIFICATIONS/RATINGS

CE, Class A

FCC, Part 15, Class A

UL/cUL Listed

C-Tick

Designed to meet NEMA TS-1/TS-2 and the Caltrans traffic signal control equipment environmental standards