stc-sc32poehs.jpg View Larger Image (in new window)

Sentech : STC-SC32POEHS

By: Sentech
Industrial, USB, & Medical Cameras
Contact us for lowest price (800) 284-2288, (858) 565-1101,, or fax (858) 300-4193
122 fps, 0.3MP, Color GigE camera, w/ IR cut filter, w/ POE

The STC-SC32POEHS is part of Sentech's Brand New Power over Ethernet High Speed GigE camera series. It features a 1/2" color VGA sensor, 122fps and communication over a 6 pin Hirose or Ethernet connector. The STC-SC32POEHS boasts a compact 35(w) x 35(H) x 55.9 (D) mm size, a user-programmable Area of Interest (AOI) and a Gamma Table that can be imported. This camera meets all industry standards for GigE Vision® and GenICam™, and is compatible with all standard industry drivers. The GigE PoEHS series is available now at an extremely low cost.

STC-SC32POEHS features include:

  • User Programmable AOI
  • High Speed Power Over Ethernet
  • 0.3 Megapixel Resolution with 122 fps


1/2” interline VGA color progressive CCD: ICX414AQ

Total Picture Element


Active Picture Element

VGA: 648 (H) x 494 (V)

Cell Size

9.9 (H) x 9.9 (V) µm

Scanning System


Vertical Frequency

122.11786 Hz at full resolution 0.97814 to 419.03186 Hz adjustable via the communication (Frame rate depends on the AOI setting) Maximum frame rate (419.03186 Hz) is when vertical resolution AOI setting is 104.

Horizontal Frequency


Pixel Frequency

50.07272 MHz

Noise Level


- @ 8Bit Output

<= 3 Digit (Gain 0 dB)

- @ 10Bit Output

<= 12 Digit (Gain 0 dB)

- @ 12Bit Output

<= 48 Digit (gain 0 dB)

Minimum Scene Illumination

43.64 Lux at F1.2, 122.27770Hz

Sync System


Video Output

Digital 8 ,10 or 12 bit Raw Data or RGB 8 bit


PoE: IEEE802.3af CLASS3 (1000BASE-T)


GigE Vision 1.2 and GeniCam 2.0 compliant

Exposure Time

Preset continuous mode: 10 seconds to 16,777,216 seconds; Preset trigger mode: 10 seconds to 16,777,216 seconds; Pulse width mode: 10 seconds to Unlimited.


Electronic iris and AGC (ON/OFF)


0 to 18.309 dB


Gamma 1.0 (Factory default) or downloadable gamma table

AOI (Area of Interest) Function

Programmable AOI setting via the communication

Smear Reduction

Selectable ON/OFF via the communication

Color Interpolation

Available on RGB output

White Balance

Auto, Manual, and push to set white balance is available on both Raw Data output and RGB output.

Trigger Mode

Edge preset trigger, pulse width trigger (unlimited exposure time)


UART communication through Ethernet Port


One opt isolated input and two open collector outputs



- Input Voltage

+10.8 to +26.4Vdc through power/IO connector or Power Over Ethernet; (Auto detection with power/IO connector prioritized)

- Consumption

12V: 3.2W / 2.9W, PoE: 3.4W / 3.1W


35 (W) x 35 (H) x 57.3 (D) mm excluding connectors

Optical Filter

IR cut filter on

Optical Center Accuracy

Positional accuracy in H and V directions: +/- 0.3 mm; Rotational accuracy of H and V: +/- 1.5 deg.


Aluminum (AC)

Lens Mount

C Mount


RJ45 connector; Power/IO connector: HR10A-10R-6PB (Hirose) or equivalent

Camera Mount Screws

Two ¼” Tripod screw holes (one each on top and bottom plate); Twelve M4 screw holes (four each on top, bottom, and two each on both side plates)


Approx. 130

Operating Temperature


- Minimum

Environmental Temperature: -5 deg. C

- Maximum

Camera housing temperature (top plate) shall not exceed 65 deg. C (This corresponds to an environmental temperature of approximately 40 deg. C)

Storage Temperature

Environmental Temperature: -30 to 65 deg. C


20Hz to 200Hz to 20Hz (5min/cycle), acceleration 10G, 3 directions 30 min. each


Acceleration 38G, half amplitude 6ms, 3 directions, 3 times each

Standard Compliancy

EMS: EN61000-6-2, EMI: EN55011


RoHS compliant

facebook.png twitter.png googleplus.png linkedin.png youtube.png pinterest.png
Prices and specifications subject to change without notice.