Call Now: 1-800-284-2288 |
10-Motor Power Supply with Ethernet to Cresnet® Bridge and Cresnet Hub |
|
|
|
|
The CSA-PWS10S-HUB-ENET Power Supply powers up to 10 Crestron® Quiet Motor Technology™ roller shade or drapery system motors through a home run to each motor, and features an Ethernet to Cresnet® bridge and a built-in, 5-segment Cresnet® hub. The embedded Ethernet to Cresnet bridge provides the flexibility necessary for a multitude of installation configurations with the added benefit of high-speed communications. Any hub set to Ethernet becomes a Cresnet hub master for any daisy-chained hubs that are set to Cresnet and connected to the hub. A local control interface with LED feedback indicators allows roller shade or drapery systems to be tested without a control system connection. In addition to network diagnostics capabilities, the CSA-PWS10S-HUB-ENET is convection cooled for silent operation and can be surface-mounted or mounted in a CAEN or CAEN-MLO enclosure.
- Support for up to 10 Crestron® roller shade motors, 10 drapery system motors, or a combination of the two up to a total of 10
- Built-in 5-segment Cresnet® hub
- Ethernet to Cresnet bridge
- Ability to remotely cycle power to each shade motor to assist in troubleshooting
- Individual per-motor overcurrent protection
- Local shade and drapery master controls
- Clear diagnostic LED indicators
- Convection cooled for silent operation
- Surface-mountable or mountable in a CAEN enclosure
| Load Rating | ||
| Total Motors Supported | Provides power for up to (10) Crestron® roller shade motors, (10) drapery system motors, or a combination of the two up to a total of (10) motors with each motor homerun to the power supply; 10 Drapery System solutions carry 145 lbs load each |
|
| Output | 24 Volts DC, 60 Watt max/output LPS 250 Watts Total Continuous Load 525 Watts 2 minutes ON, 10 minutes OFF Limited Duty Cycle |
|
| Load Protection | (10) Self-resetting thermal fuses, (1) per output | |
| Power Requirements | ||
| Line Power | 110-240 Volts AC, 50/60 Hz, 5.5 Amps max at 110 Volts AC, 2.7 Amps max at 240 Volts AC | |
| Connections | ||
| NET HOST IN, OUT | (2) 4-pin 5 mm detachable terminal blocks; Cresnet® slave ports, paralleled; Connect to Cresnet control network in Cresnet mode,[1] power not supplied to these connections; Cresnet power and data pass-through; Used to daisy-chain to additional CSA-PWS10S-HUB-ENET modules when in Ethernet mode[1,2] |
|
| A-E, 1-10 | (10) 4-pin 5 mm detachable terminal blocks comprising (2) Cresnet ports per each of the (5) hub segments | |
| LAN | (1) 8-pin RJ45, female; 10Base-T/100Base-TX Ethernet port |
|
| USB | (1) USB Type B female, USB computer console port | |
| Line Power | (1) Attached input power cable (~10 in long, 254 mm) with inline IEC 60320 C14 main power inlet; Connects to AC power source using grounded 3-prong IEC cord (included) |
|
| MEMORY CARD | Not used | |
| LED Indicators | ||
| PWR 1-10 | (10) Green LEDs, indicate 24 Volts present at each corresponding output | |
| NET A-E | (5) Amber LEDs, indicate Cresnet or Ethernet activity on each corresponding hub segment | |
| NET HOST | (1) Amber LED, indicates Cresnet activity with control system | |
| MSG | (1) Red LED, indicates error messages and Test mode | |
| Buttons | ||
| MODE | (1) Switch, sets the unit to either Cresnet or Ethernet mode; CRES: Enables Cresnet communications, unit functions as a slave device; All daisy-chained hubs except for the master must be set to CRES[1,2] LAN: Enables Ethernet communications, unit functions as a master device; Standalone units set to LAN must be directly connected to a LAN source[1] |
|
| MASTER UP | (1) Pushbutton, press and hold to raise/open all connected shades/drapery | |
| MASTER DOWN | (1) Pushbutton, press and hold to lower/close all connected shades/drapery | |
| TEST | (1) Pushbutton, initiates or terminates diagnostic test | |
| RESET | (1) Recessed pushbutton, forces hardware reset | |
| Housing | ||
| Enclosure | Metal, grey | |
| Mounting | Mounts in a CAEN or CAEN-MLO enclosure, 16-gauge galvanized steel enclosure with vented grey steel cover; Surface-mountable on a wall (indoor use only) |
|
| Environmental | ||
| Temperature | 32° to 104° F (0° to 40° C) | |
| Humidity | 10% to 90% RH (non-condensing) | |
| Dimensions | ||
| Height | 7.71 in (196 mm) | |
| Width | 6.32 in (162 mm) | |
| Depth | 3.08 in (78 mm) | |
| Weight | ||
| 3 lbs (1.4 kg) | ||
| csa-pws10s-hub-enet-specs.pdf | datasheet |
Call Now: 1-800-284-2288 |
|||||
Email Us: sales@avsupply |
|||||
|
© 1996 - 2024 | All Rights Reserved
Audio Video Supply Inc.
4542 Ruffner St. Suite 220
San Diego, CA 92111
Prices and specifications subject to change without notice.