The Imaging Source DFG-LC4E is a 4 input Frame grabber. This DFG LC4E grabber comes with up to 768x576 pixels and up to 30 images/second.
 

The Imaging Source DFG-MC4-PCIE is a 4 input Frame grabber. This DFG MC4 PCIE grabber comes with up to 768x576 pixels and up to 30 images/second.
 

The Imaging Source DFG/SV1 is a 3 Input Frame grabber.

The Imaging Source DFG-SV1-LP is a 3 input Frame grabber. This DFG SV1 LP grabber comes with up to 768x576 pixels and up to 30 images/second.
 

The Imaging Source DFG-SV1-LP-PCIE is a 3 input Frame grabber. This DFG SV1 LP PCIE grabber comes with up to 768x576 pixels and up to 30 images/second.
 

Video formats	PAL/NTSC, RS-170/CCIR
Max resolution	PAL= 768x576 at 25 fps; NTSC= 640x480 at 30 fps
Analog inputs	2xRCA (cinch); 1xY/C (S-Video); Multiplexed
Bus interface	32 Bit - PCI Express, Bus Mastering
Color formats	YUV 4:2:2, YUV 4:1:1, YUV 4:1:0, RGB 32, RGB 24, RGB 8

The Imaging Source DFG-SV1-PCIE is a 3 input Frame grabber. This DFG SV1 PCIE grabber comes with up to 768x576 pixels and up to 30 images/second.
 

The Colorado Video 441CS Video Frame Store, Video Frame Grabber, Video Freeze Frame or Video Memory, is a full frame, high resolution, video memory for NTSC or PAL composite video....

The Colorado Video 448S Video Frame Averager, Video Freeze Frame or Video Frame Grabber creates a freeze frame picture image, upon request, representing the average of a selected n...

This item has been DISCONTINUED.

The Domino series is a range of high-end PCI and PCI Express frame grabbers for analog cameras. DOMINO-ALPHA-2

Form factor	32-bit, 33 MHz PCI
Analog cameras	Single-tap = Up to 4, Dual-tap = Up to 2
Video connector	On the bracket = 2 x HD15
Sampling resolution / Max. frequency	Max. line rate operation a = 8 bits @ 32 MHz
Max. line rate	Synchronous mode = 31.5 kHz, Asynchronous mode = 31.5 kHz

The Domino series is a range of high-end PCI and PCI Express frame grabbers for analog cameras. DOMINO-HARMONY supports any system function associated to industrial acquisition, su...

Form factor	64-bit, 66 MHz PCI
Analog cameras	Single-tap = 2, RGB = 1
Video connector	On the bracket = 2 x HD15, Internally = 1 x 10-pin header
Sampling resolution / Max. frequency	Max. line rate operation a = 10 bits @ 40 MHz
Max. line rate	Synchronous mode = 42 kHz, Asynchronous mode = 31.5 kHz

The Domino series is a range of high-end PCI and PCI Express frame grabbers for analog cameras. DOMINO-MELODY supports any system function associated to industrial acquisition, suc...

Form factor	32-bit, 33 MHz PCI, Low Profile compatible
Analog cameras	Single-tap = 1
Video connector	On the bracket = 1 x HD15, Internally = 1 x 10-pin header
Sampling resolution / Max. frequency	Max. line rate operation a = 10 bits @ 40 MHz
Max. line rate	Synchronous mode = 42 kHz, Asynchronous mode = 31.5 kHz

The Domino series is a range of high-end PCI and PCI Express frame grabbers for analog cameras. DOMINO-SYMPHONY supports any system function associated to industrial acquisition, s...

Form factor	x1 PCI Express Full height, half length
Analog cameras	Single-tap = 4
Video connector	On the bracket = 1 x HD44, Internally = 1 x 10-pin header
Sampling resolution / Max. frequency	Max. line rate operation a = 10 bits @ 65 MHz
Max. line rate	Synchronous mode = 52.5 kHz, Asynchronous mode = 52.5 kHz (digital vertical synch.)

The DPICT 10011-001 Aexeon is a low-cost, full-featured video frame grabber board for analog camera solutions. Aexeon accepts multiple composite, S-Video, or component video inputs...

The DPICT 10012-001 Aexeon is a low-cost, full-featured video acquisition board for analog cameras. Available in either PCI or PCI Express formats, Aexeon incorporates a digital me...

The DPICT 10021-001 Aexeon is a low-cost, full-featured video acquisition board for analog cameras. Available in either PCI or PCI Express formats, Aexeon incorpor...

The DPICT 10022-001 Aexeon is a low-cost, full-featured video acquisition board for analog cameras. Available in either PCI or PCI Express formats, Aexeon incorporates a digital me...

The DPICT 10031-001 Aexeon LT PCI is a low cost, full-featured video frame grabber board for analog camera solutions.  Aexeon LT accepts composit...

The DPICT 10032-001 Aexeon LT PCI is a low cost, full-featured video frame grabber board for analog camera solutions.  Aexeon LT accepts composite, S-video, both ...

The DPICT 10042-001 Aexeon HDS video input circuitry digitizes between multiple component, S-Video, or composite video signals. With plenty of I/O triggers and ext...

The DPICT 10503-001 nVision from dPict Imaging is a multi-format intelligent video acquisition device for mobile or remote capture. nVision digiti...

The DPICT 10533-001 nVision GX2 from dPict Imaging the next-generation multi-format intelligent video acquisition device for mobile or remote capture. nVision GX2 digitizes and tra...

The 11021-002 Nexeon CL is a low-cost, full-featured video frame grabber for digital camera solutions with the Camera Link standard. Nexeon supports the Base configuration of the C...

The 11042-001 Nexeon HD is a full-featured video frame grabber for high-definition video display and capture. It supports video inputs from standard and HDTV resolutions as well as...

The 99503 nVision I/O Carrier board provides for standard connections for video, communications, and trigger I/O.

The 99504 nVision GX2 I/O Carrier board provides for standard connections for video, communications, and trigger I/O

This product has been discontinued. Please consider another Grablink Series product, such as Grablink E...

Form factor	64-bit, 66 MHz PCI, Full height, half length
Camera Link configuration	Base
Max pixel-clock frequency	24 bits @ 85 MHz
Line scan	ADR Technology™
Delivery bandwidth	240 MB/s

The Euresys PIC-OLO is a top-quality video acquisition card compatible with standard PAL or NTSC cameras. They are dedicated to high-end applications in the fields of video surveil...

PCI interface(s)	32-bit, 33 MHz PCI
Video signals	Interlaced composite PAL/NTSC S-Video interlaced
Video resolution	Square - Broadcast, QCIF => Full D1
Video acquisition rate	Up to 50/60 fps, up to 25/30 ips
Nr. of real time cameras per card	1

This product has been discontinued. Please consider another Picolo series product, such as the Picolo Pro...

PCI interface(s)	64-bit, 66 MHz PCI or PCI Express x1
Video signals	Interlaced composite PAL/NTSC
Video resolution	Square - Broadcast, QCIF => Full D1
Video acquisition rate	200/240 fps, up to 100/120 ips constantly available
Nr. of real time cameras per card	4

The Euresys PICOLO ALERT PCIe is a top-quality video acquisition card compatible with standard PAL or NTSC cameras. They are dedicated to high-end applications in the fields of vid...

PCI interface(s)	64-bit, 66 MHz PCI or PCI Express x1
Video signals	Interlaced composite PAL/NTSC
Video resolution	Square - Broadcast, QCIF => Full D1
Video acquisition rate	200/240 fps, up to 100/120 ips constantly available
Nr. of real time cameras per card	4

This product has been discontinued. Please consider another Picolo series product, such as the Picolo Pro...

This product has been discontinued. Please consider another Picolo series product, such as the Picolo Pro...

This product has been discontinued. Please consider another Picolo series product, such as the Picolo Pro...

This product has been discontinued. Please consider another Picolo series product, such as the Picolo Pro...

PCI interface(s)	64-bit, 66 MHz PCI
Video signals	Interlaced composite PAL/NTSC
Video resolution	Square - Broadcast, QCIF => Full D1
Video acquisition rate	Up to 200/240 fps, up to 100/120 ips
Nr. of real time cameras per card	4

This product has been discontinued. Please consider another Picolo series product, such as the Picolo Pro...

PCI interface(s)	PCI Express x1
Video resolution	4CIF, 2CIF, CIF, QCIF
Video acquisition rate	400/480 ips
Nr. of real time cameras per card	16
Max. number of cameras per card	16

This product has been discontinued. Please consider another Picolo series product, such as the Picolo Pro...

PCI interface(s)	PCI Express x1
Video resolution	4CIF, 2CIF, CIF, QCIF
Video acquisition rate	100/120 ips
Nr. of real time cameras per card	4
Max. number of cameras per card	4

This product has been discontinued. Please consider another Picolo series product, such as the Picolo Pro...

PCI interface(s)	PCI-104
Video resolution	4CIF, 2CIF, CIF, QCIF
Video acquisition rate	100/120 ips
Nr. of real time cameras per card	4
Max. number of cameras per card	4

This product has been discontinued. Please consider another Picolo series product, such as the Picolo Pro...

PCI interface(s)	PCI Express x1
Video resolution	4CIF, 2CIF, CIF, QCIF
Video acquisition rate	200/240 ips
Nr. of real time cameras per card	8
Max. number of cameras per card	8

The EPIX Analog Video for PCI Express PIXCI-A310 video frame grabber acquires images from monochrome or component RGB color, interlaced or progressive scan, from cameras or other v...

Video Formats	UXGA, WSGA , WXGA, SXGA , SXGA, XGA, SVGA, VGA, RS343, CCIR, RS-170, and others
Supported Resolutions Include	1920x1080p, 1920x1080i, 1280x720p, 720x480p, 720x576p, and others
Bit Depth	30, 24, 10, or 8 bits per pixel
Pixel Clock Range	12 MHz to 165 MHz
Maximum PCIe Data Rate	700 Megabyte per second sustained data transfer

The EPIX Camera Link for PCI PIXCI-CL1 accepts data from a Camera Link camera while providing exposure, reset, and serial control. The PIXCI® CL1 capture and control board reduces...

Resolution	8 to 4,096 pixels per line; 1 to 4,096 lines per image (area scan); 1 to 65,534 lines per image (line scan)
Signals	Differential RS-644; Differential Trigger IN / Strobe OUT; 2 TTL input/outputs
Connections	1 26-pin Camera Link; 1 9-pin D-Subminiature; 2 10-pin headers
Maximum frame rate	Camera Dependent
CE / FCC Certification	PIXCI CL1 was tested per EMC directive 89/336/EEC and performed to class B

The EPIX Camera Link for PCI PIXCI-CL2 frame grabber supports Full, Medium, and Base configuration Camera Link cameras. Compatible with the 64-bit/ 66MHz PCI bus, the CL2 board int...

PCI Bus

64-bit/66MHz or PCI-X

The EPIX Camera Link for PCI PIXCI-D2X is designed for scientific and machine vision applications that require the highest image quality. To insure that precise camera data is alwa...

Resolution	8 to 4,096 pixels per line, 1 to 4,096 lines per image (area scan), 1 to 65,534 lines per image (line scan)
Signals	Differential RS-644 or RS-422 camera / board signaling (camera dependent). Differential Trigger IN / Strobe OUT 2
Maximum frame rate	Camera Dependent
Connections	1 68-pin (SCSI II) cable receptacle, 2 10-pin headers
CE / FCC Certification	PIXCI D2X was tested per EMC directive 89/336/EEC and performed to class B.

The EPIX Camera Link for PCI PIXCI-D3X is a PCI-compatible imaging board supporting camera configurations with 3 to 8 data channels, or with 30 to 64 total data bits - cameras that...

Resolution	8 to 4,096 pixels per line, 1 to 4,096 lines per image (area scan), 1 to 65,534 lines per image (line scan)
Signals	Differential RS-644, Differential Trigger IN / Strobe OUT (Optional "TTL Module" allows TTL Trigger IN and TTL Strobe OUT)
Connections	1 100-pin cable receptacle, 2 10-pin headers
Maximum frame rate	Camera Dependent
CE / FCC Certification	PIXCI D3X was tested per EMC directive 89/336/EEC and performed to class B.

The EPIx PIxCI e104x4 is a PCIe/104 Frame Grabber For Embedded Camera Link Applications.

The EPIX Camera Link for PCI Express PIXCI-E4DB frame grabber connects two Base camera link cameras to the PCI Express bus. The PIXCI E4DB is handled by EPIX software as if two PIX...

The EPIX Camera Link for PCI Express PIXCI-E8 is a Camera Link frame grabber supporting the highest data rate cameras. The PIXCI E8 supports more than 900 Extended, Full, Medium, B...

The EPIX Camera Link for PCI Express PIXCI-EB1 is a low cost, low profile frame grabber with Power over Camera Link (PoCL). The PIXCI EB1P is compatible with all area scan and line...

Signal Input & Output	EIA RS-644 (LVDS) Drivers & Receivers support pixel clock frequencies up to 85 MHz
Conections	One 26-pin 3M MDR Camera Link connector for Base. 6-pin connector for Trigger, Frame Enable, and Strobe. Camera Link cables available
Data Transfers	Supports cameras with data output rates up to 250 MBytes/second. 64-bit memory addressing
Bus Requirements	PCI Express x1 slot. Operates in PCI Express x16, x8, x4, or x1 slot
Dimesions	8.38 cm long by 6.88 cm high (3.30" long x 2.71" high)

The PIXCI EB1mini frame grabber provides a vertical Camera Link SDR connector with FPGA on a single printed circuit board using a full size mini card slot. At the maximum Camera Li...

The PIXCI EB1miniF moves the Camera Link connector to a separate board and connects the two with detachable flat ribbon cable. This allows for more mounting options in space constr...

The PIXCI EB1miniG has the Camera Link connector on a separate circuit board and connects to the FPGA circuit board with two very flexible cables. This version requires less spac...

The PIXCI EB1miniH has an SDR Camera Link connector and FPGA on a separate circuit board for mounting to the side of a small chassis. Two very flexible cables connect to a half len...

The EPIX Camera Link for ExpressCard PIXCI-EC1 frame grabber supports all Full, Medium, and Base configuration Camera Link cameras with bandwidth requirements of 191 Megabytes (152...

The EPIX Camera Link for ExpressCard PIXCI-ECB1 frame grabber supports all Base configuration Camera Link cameras with bandwidth requirements of 191 Megabytes (1528 Mbits) per seco...

The EPIX Camera Link for ExpressCard PIXCI ECB 134 base Camera Link frame grabber plugs into an ExpressCard/34 or ExpressCard/54 slot in a notebook computer. With 200 megabyte per ...

The EPIX Camera Link for ExpressCard PIXCI-ECB2 frame grabber provides two interfaces for any two Base camera link cameras. The PIXCI ECB2 is handled by EPIX' software as if two PI...

The EPIX Camera Link for PCI Express PIXCI-EL1 frame grabber supports Full, Medium, and Base configuration Camera Link cameras. Compatible with the PCI Express x1 (by one) bus, the...

The EPIX Camera Link for PCI Express PIXCI-EL1DB frame grabber provides two interfaces for any two Base camera link cameras. The PIXCI EL1DB is handled by EPIX' software as if two ...

The EPIX Silicon Video Frame Grabbers PIXCI-SI2 frame grabber provides low cost high resolution capture from two SILICON VIDEO cameras. Two cameras, operating at maximum resolution...

Bus requirements	PCI Express bus x1 thru x16 slot.
Power requirements	1.56 Amps @ 3.3 Volts, 0.21 Amps @ 12 Volts With two SV9T001C 3-megapixel color cameras at 48 MHz pixel clock.
Dimensions (excluding bracket)	3.94 inches long by 2.75 inches high, 100 mm long by 70 mm high (Available with standard or low profile bracket.)
Transfer rates	Provides burst transfer rates, from cameras to on-board memory, up to 280 megabytes per second. Transfer rates from on-board memory through the PCI Express bustypically reach 202 megabytes per second
On-board memory	64 megabytes of frame buffer memory

The EPIX Silicon Video Frame Grabbers PIXCI-SI2 frame grabber provides low cost high resolution capture from two SILICON VIDEO cameras. Two cameras, operating at maximum resolution...

The EPIX Silicon Video Frame Grabbers PIXCI-SI4 frame grabber supports 1 to 4 SILICON VIDEO cameras. Cameras may be identical or mixed, and can operate simultaneously or independen...

The EPIX Analog Video for PCI PIXCI-SV5 is a video-rate frame grabber that captures high quality, uncompressed, scientific quality digital images from standard analog output video ...

4 Pin DIN	S-Video Input
Two BNC-Jacks	Composite Video Inputs
DB15	TTL I/O Triggers
Color or Monochrome Video Acquisition	S-Video, RS-170, CCIR, NTSC, PAL
Resolution-Pixels	754x480: RS-170, NTSC, S-Video 922x580: CCIR, PAL, S-Video

The EPIX Analog Video for PCI PIXCI-SV5A offers 3 multiplexed BNC inputs. All other features on the PIXCISV5A are identical to the PIXCI SV5.

The EPIX Analog Video for PCI PIXCI-SV5B offers 1 BNC input and 1 Loop Thru BNC output. The S-Video and trigger connectors are removed to allow for a low-profile PCI form factor wi...

Capture FIELDs to Double the Capture Rate	If fast capture rate is more important than vertical resolution, then selecting the Field at Field mode doubles a field capture rate while cutting vertical resolution in half. Capture 50 fields per second from a PAL or CCIR camera; capture 60 fields per second from an NTSC or RS-170 camera
Capture FIELDs instead of full Frames	If memory or storage capacity is limited, and field resolution is sufficient, then selecting, Field at Frame allows the capturing of a sequence of fields instead of a sequence of frames (at the camera’s 25 frames per second (fps) PAL/CCIR or 30 fps NTSC/RS-170). The PIXCI SV5 Video Format menu allows resolution selection in single pixel increments for greater control, but Field at Frame offers a simple “one-click” option for added convenience
Capture Frame at Frame	This is the default capture option offering maximum vertical resolution images at the camera’s frame rate. Selected Capture from Three Video Sources using one PIXCI SV5(A): The PIXCI SV5 imaging board features a 3-input video multiplexer that allows signal selection from two BNC and one S-Video input. The PIXCI SV5A allows signal selection from three BNC inputs
Capture from Multiple PIXCI SV5 boards	As many as eight PIXCI® SV5 boards can be installed in one computer allowing selected capture from multiple video sources controlled by a single program. Because the multiplexer on each board allows connection of up to 3 sources, a total of 24 sources can be connected. Simultaneous capture from up to eight sources is possible – subject to the bandwidth constraints of the PCI bus or buses on the selected motherboard. There are motherboards with multiple PCI buses. Each PCI bus has a bandwidth of approximately 110 megabytes per second. Capture Short Sequence with Selected Image Save: The XCAP-Lite imaging program, provided at no charge with the purchase of the PIXCI SV5 imaging board, allows sequence capture into as much as 64 Mbytes of computer memory. Individual images can be saved one at a time
Capture and Save Sequence into PC Memory	The optional XCAP-Ltd imaging program allows maximum resolution and frame rate sequence capture into the computer’s available memory, to a maximum of approximately 3 to 3.5 gigabytes. At full resolution and frame rate, capture a color sequence with duration of 150 seconds, or a monochrome sequence with duration of 300 seconds. Capture and Save Sequence to Hard Drive: The optional XCAP-Std imaging program ($1495) allows maximum resolution and frame rate sequence capture direct to a 7200 rpm drive or to a RAID system. Using a 750 gigabyte drive, XCAP-Std can capture a full resolution uncompressed sequence for up to 5 hours from a color source, or for up to 10 hours from a monochrome source. Longer sequence capture is available with more drives

The EPIX Analog Video for PCI PIXCI-SV5L offers 2 Mini BNC and 1 S-Video multiplexed inputs. The PIXCISV5L trigger connector has been removed to allow for a low-pr...

Capture FIELDs to Double the Capture Rate	If fast capture rate is more important than vertical resolution, then selecting the Field at Field mode doubles a field capture rate while cutting vertical resolution in half. Capture 50 fields per second from a PAL or CCIR camera; capture 60 fields per second from an NTSC or RS-170 camera
Capture FIELDs instead of full Frames	If memory or storage capacity is limited, and field resolution is sufficient, then selecting, Field at Frame allows the capturing of a sequence of fields instead of a sequence of frames (at the camera’s 25 frames per second (fps) PAL/CCIR or 30 fps NTSC/RS-170). The PIXCI SV5 Video Format menu allows resolution selection in single pixel increments for greater control, but Field at Frame offers a simple “one-click” option for added convenience
Capture Frame at Frame	This is the default capture option offering maximum vertical resolution images at the camera’s frame rate. Selected Capture from Three Video Sources using one PIXCI SV5(A): The PIXCI SV5 imaging board features a 3-input video multiplexer that allows signal selection from two BNC and one S-Video input. The PIXCI SV5A allows signal selection from three BNC inputs
Capture from Multiple PIXCI SV5 boards	As many as eight PIXCI® SV5 boards can be installed in one computer allowing selected capture from multiple video sources controlled by a single program. Because the multiplexer on each board allows connection of up to 3 sources, a total of 24 sources can be connected. Simultaneous capture from up to eight sources is possible – subject to the bandwidth constraints of the PCI bus or buses on the selected motherboard. There are motherboards with multiple PCI buses. Each PCI bus has a bandwidth of approximately 110 megabytes per second. Capture Short Sequence with Selected Image Save: The XCAP-Lite imaging program, provided at no charge with the purchase of the PIXCI SV5 imaging board, allows sequence capture into as much as 64 Mbytes of computer memory. Individual images can be saved one at a time
Capture and Save Sequence into PC Memory	The optional XCAP-Ltd imaging program allows maximum resolution and frame rate sequence capture into the computer’s available memory, to a maximum of approximately 3 to 3.5 gigabytes. At full resolution and frame rate, capture a color sequence with duration of 150 seconds, or a monochrome sequence with duration of 300 seconds. Capture and Save Sequence to Hard Drive: The optional XCAP-Std imaging program ($1495) allows maximum resolution and frame rate sequence capture direct to a 7200 rpm drive or to a RAID system. Using a 750 gigabyte drive, XCAP-Std can capture a full resolution uncompressed sequence for up to 5 hours from a color source, or for up to 10 hours from a monochrome source. Longer sequence capture is available with more drives

The EPIX Analog Video for PCI PIXCI-SV5S offers 2 BNC and 1 S-Video multiplexed inputs. The PIXCISV5S adds additional circuitry that separates the vertical sync. f...

Capture FIELDs to Double the Capture Rate	If fast capture rate is more important than vertical resolution, then selecting the Field at Field mode doubles a field capture rate while cutting vertical resolution in half. Capture 50 fields per second from a PAL or CCIR camera; capture 60 fields per second from an NTSC or RS-170 camera
Capture FIELDs instead of full Frames	If memory or storage capacity is limited, and field resolution is sufficient, then selecting, Field at Frame allows the capturing of a sequence of fields instead of a sequence of frames (at the camera’s 25 frames per second (fps) PAL/CCIR or 30 fps NTSC/RS-170). The PIXCI SV5 Video Format menu allows resolution selection in single pixel increments for greater control, but Field at Frame offers a simple “one-click” option for added convenience
Capture Frame at Frame	This is the default capture option offering maximum vertical resolution images at the camera’s frame rate. Selected Capture from Three Video Sources using one PIXCI SV5(A): The PIXCI SV5 imaging board features a 3-input video multiplexer that allows signal selection from two BNC and one S-Video input. The PIXCI SV5A allows signal selection from three BNC inputs
Capture from Multiple PIXCI SV5 boards	As many as eight PIXCI® SV5 boards can be installed in one computer allowing selected capture from multiple video sources controlled by a single program. Because the multiplexer on each board allows connection of up to 3 sources, a total of 24 sources can be connected. Simultaneous capture from up to eight sources is possible – subject to the bandwidth constraints of the PCI bus or buses on the selected motherboard. There are motherboards with multiple PCI buses. Each PCI bus has a bandwidth of approximately 110 megabytes per second. Capture Short Sequence with Selected Image Save: The XCAP-Lite imaging program, provided at no charge with the purchase of the PIXCI SV5 imaging board, allows sequence capture into as much as 64 Mbytes of computer memory. Individual images can be saved one at a time
Capture and Save Sequence into PC Memory	The optional XCAP-Ltd imaging program allows maximum resolution and frame rate sequence capture into the computer’s available memory, to a maximum of approximately 3 to 3.5 gigabytes. At full resolution and frame rate, capture a color sequence with duration of 150 seconds, or a monochrome sequence with duration of 300 seconds. Capture and Save Sequence to Hard Drive: The optional XCAP-Std imaging program ($1495) allows maximum resolution and frame rate sequence capture direct to a 7200 rpm drive or to a RAID system. Using a 750 gigabyte drive, XCAP-Std can capture a full resolution uncompressed sequence for up to 5 hours from a color source, or for up to 10 hours from a monochrome source. Longer sequence capture is available with more drives

The EPIX Analog Video for PCI Express PIXCI-SV7 digitizes analog video from one or two standard composite video cameras (NTSC, RS-170, PAL or CCIR). The two inputs are independent,...

Camera video formats

TSC, RS-170, PAL or CCIR

The EPIx PIxCI SV8 is a Frame grabber for color and monochrome analog video: S-Video, NTSC, PAL, RS-170, CCIR.