Optera Multi-Sensor 180°, 270°, 360° Panoramic 12 MP IP Cameras with SureVision 2.0

The Optera™ IMM Series camera with SureVision™ 2.0 provides a panomersive experience with seamless situational awareness which provides stitched and blended panoramic views. The IMM Series also enables you to zoom in for detail within multiple intuitive immersive views from a video management system (VMS). Other multi-imager solutions can be disjointed with separate streams out of order. The IMM Series transparently integrates video across all sensors in the camera, presenting a seamless user experience from setup to viewing.

IMM Series camera options include 180-, 270-, or 360-degree models. All models include a camera in a compact in-ceiling mount, surface mount, or pendant enclosure that is ready to install. All models feature a robust metal tamper-resistant design and carry an IK10 impact rating for vandal resistance. The Environmental Vandal model features worry-free use in a wide range of challenging operating conditions. In-ceiling models have a back box that is plenum rated per 2008 NEC article 300.22(C)(2).

Available Models Differ in Field of View, Environment, Mount, and trim color(for indoor models)

• Constant, seamless situational awareness
• Zoom in for detail live or retrospectively with client-side dewarping
• Multiple immersive PTZ views at video management system (VMS)
• Up to 12 Megapixel (4 x 3 MPx) resolution for better detail at a distance
• Up to 30 frames per second (fps)
• Outstanding WDR and low-light performance at the same time
• Pelco H.264 Smart Compression Technology
• Eight Pelco video analytic behaviors
• Local storage (Micro SD)
• Pelco Camera Link
• ONVIF Profile S, Profile G, and Profile Q conformant
• Compatible with Pelco VideoXpert™, VideoXpert™ Professional, Digital Sentry®, Endura™ (In Tiled Mode), and third-party VMS partners

CAMERA

Imaging Device 1/3.2-in.

Imager Type CMOS

Imager Readout Progressive scan

Maximum Resolution 12 MP (4x) 2048 x 1536 x 4

Signal-to-Noise Ratio >50 dB

Day/Night Capabilities Yes

Mechanical IR Cut Filter Yes, (ON/OFF/AUTO selectable) with different set points

Wide Dynamic Range: >120 dB

LENS

AUDIO

Streaming Bidirectional: full or half duplex

Input/Output 600 ohm differential, 1Vp-p max. signal level

Compression G.711 PCM 8 bit, 8 kHz mono at 64 kbit/s

MECHANICAL

Dome Attenuation Clear f/0.0 light loss Smoked f/1.0 light loss

Pan Adjustable (All Models) 370°

Tilt Adjustable (180 Model) 0° - 180°

PHYSICAL 

Unit Weight: In Ceiling 1.5 kg (3.3 lb) Surface Mount 1.7 kg (3.9 lb)   Pendant Mount   1.7 kg (3.9 lb)

Shipping 2.0 kg (4.3 lb)   All models

ENVIRONMENTAL

Operating Temperature

• Indoor Vandal –10° to 50°C (14° to 122°F)†
• Environmental Vandal –40° to 50°C (–40° to 122°F)†

† Thermostatically controlled active heating and cooling.

Operating Humidity

• Indoor Vandal 15 to 85%, RH noncondensing
• Environmental Vandal 10 to 95%, RH condensing

Impact Resistance IK10 (20J) Shock and Vibration EN50155 Category 1, Class B; IEC 60068:2-6 and 2-27; ISTA-2A, Sequence 5, MIL810G

Storage Temperature –40° C to 60° C (–40° F to 140° F)

Storage Humidity 15% to 85%, noncondensing

ELECTRICAL

Network Port RJ-45 connector for 1000Base-T 1 Gigabit/sec Auto MDI/MDI-X PoE+; Class 4

Cable Type Category 5 or better

Input Power PoE+ (IEEE 802.3at, Class 4)

Power Consumption Without Heater 17 Watts With Heater 23 Watts Notice: Total camera power consumption attached to a multi-port PoE+ switch must not exceed the total PoE+ power provided by the switch.

Local Storage Micro SD, SDHC

Alarm

• Unsupervised Detects open or closed alarm state
• Supervised Detects open and short alarm state with external 1-kohm resistor to detect alarm tampering
• Input 3.5 VDC maximum, 3.5 mA maximum

Relay Output ±32 VDC maximum, 150 mA maximum

NETWORK

Users Unicast Up to 20 simultaneous users depending on the resolution settings, and frame rate Multicast Unlimited users H.264

Security Access Password protected Software Interface Web browser view and setup

Supported Protocols TCP/IP, UDP/IP (Unicast, Multicast IGMP), UPnP, DNS, DHCP, RTP, RTSP, NTP, IPv4, IPv6, SNMP v2c/v3, QoS, HTTP, HTTPS, SSH, SSL, SMTP, FTP, ARP, ICMP, and 802.1x (EAP) Note: IPv6 supports mixed IPv4 and IPv6 installations, but not IPv6-only deployments.

VIDEO

Video Streams Set of streams to deliver full resolution views; secondary stream that comprises a lower resolution mosaic of above streams

Frame Rate(s) User selectable up to 30 fps

Video Encoding H.264 High, Main, or Base profiles; MJPEG (mosaic stream only)

Bit Rate Default maximum for Constrained Variable Bit Rate (CVBR) at maximum resolution and frame rate

WEB CLIENT MINIMUM SYSTEM REQUIREMENTS

Processor Intel® Core™ i3 processor, 2.4 GHz

Operating System Microsoft Windows® 10, Windows® 7 (32- and 64-bit), or Window Vista®; or Mac® OS X 10.9 (or later)

Memory 4 GB RAM

Network Interface 100 Mbps (or greater)

Monitor Minimum of 1024 x 768 resolution, 16- or 32-bit pixel color resolution

Web Browser Internet Explorer® 8.0 (or later) or Mozilla® Firefox® 35 (or later), Google® Chrome 40 (or later) WebGL 2.0 (or later)

VMS MINIMUM SYSTEM REQUIREMENTS

Operating System Windows® 7 64-bit (or later)

Video Memory 2 GB

System Memory 8 GB

Processor Intel® Core™ i7 2.0 GHz (or better)

ANALYTICS

Open API The Pelco API can transmit behavior alarm data to third-party applications.

INTEGRATION

Pelco System Integration Pelco VideoXpert, VideoXpert Professional, Digital Sentry, Endura (in Tiled Mode)

Open API Pelco API, Panomersive SDK, ONVIF Profile S, G, and Q

SOFTWARE FEATURES

• Multilingual user interface: English, French, Italian, German, Spanish, Portuguese, Russian, Chinese, Turkish
• 32 window blanks, configurable in size
• Password protection
• Snapshot with JPEG capture
• Text overlay metadata for camera name, time, date

CERTIFICATIONS/RATINGS

• CE, Class A
• FCC Part 15, Class A
• ICES-003, Class A
• UL/cUL Listed
• C-Tick
• KC
• CB Scheme ITE
• NEMA Type 4X, and IP66 rating (Environmental Vandal)
• RoHS, Lead Free, REACH
• NTCIP 1205
• IEC 62676 image quality measurement