Call Now: 1-800-284-2288 |
16 Channel Power Supply Cable Passive Integrator Hub |
|
|
The NVT 16 Channel Power Supply Cable Passive Integrator Hub NV-16PS10-PVD combines a 1 Amp/channel power supply with pass through video and telemetry data, for up to 16 cameras, all over UTP wire. Designed for installation in the wiring/IDF telecom closet, or at the Control/MDF room, the NV-16PS10-PVD consolidates connectivity via standard 4-pair RJ45 EIA/TIA 568B compliant premises wiring and pinouts.
At the camera, Power, Video and Data connections are made using a PVD transceiver via an RJ45 connector and a single 4-pair cable. Control/MDF room connections are achieved with a single 4-pair RJ45 cable for each group of four cameras. Consolidated P/T/Z telemetry data, if required, passes through the NV-16PS10-PVDs data path, and is connected to the controller via another 4-pair RJ45 cable.
NV-16PS10-PVD features include:
→ Provides Class 2 SELV camera power and pass-through video and telemetry data connectivity for up to 16 cameras, each via a single RJ45 4-pair UTP cable
→ Standard telecom/datacom structured cabling pinouts per EIA/TIA 568B
→ Independently selectable 24 or 28VAC with 1 Amp max per channel
→ Automatic-reset fault protection; transient protection
→ Individually floating outputs ensure total ground-loop immunity
→ Frequency response DC to 10MHz (see Recommended Distance Chart)
→ Diagnostic LEDs show load/no load, miswires, and overload conditions
→ Use with the NV-216A-PV or NV-218A-PVD transceivers or the NV-226J-PV transmitter at the camera
→ Power cameras via UTP over significant distances (see Power Distance Chart) 1 U high; 12 deep; wall, desk, or rack-mountable
→ Limited lifetime warranty
Video Frequency response | DC to 10 MHz |
Video Attenuation | 0.5 dB typ |
Video Common-mode / Differential-mode rejection | 15 KHz to 5 MHz 60 dB typ |
Video Impedance Coax, female BNC | 75 ohmsVideo Impedance UTP, RJ45: 100 ohms |
Network Wiring | One four-pair Cat5 or better per channel |
Camera Power | Each camera is powered by a fully isolated (floating) Class 2 SELV output, individually switchable 24VAC / Off / 28 VAC at up to 1 Amp. Each output is individually thermistor protected for auto=reset after fault removal |
Power inlet | IEC with molded power cord (included) |
Power Input On-Off Switch | Rear panel |
Power Input Voltage | 115 / 230 VAC |
Power Input Current | 3.0 / 1.5 Amps |
Power Input Frequency | 50 / 60 Hz |
Power Input Protection | 5A slo-blo 8 x 20mm fuse and thermal shutdown |
Power Input Wattage | 325 Watts |
Power Input Heat | (power supply only) 125 BTU / hour (power supply with cameras) 1,200 BTU / hour |
Blue LED | System power on |
Per-channel LED indicates Off | No load connected |
Per-channel LED indicates Green | Load connected and working |
Per-channel LED indicates Amber | Mis-wiring detected |
Per-channel LED indicates Red | Overload shutdown condition |
Ambient Temperature | -4 to 122 °F (-20 to 50 °C) airflow: 4 ft3/min (0,1m3/min) |
Humidity (non-condensing) | 0 to 95% |
Transient Immunity | per ANSI 587 C62.41 |
Dimensions including connectors | 19in wide, 1.73in high, 12in deep (483mm wide, 44mm high, 305mm deep |
Weight | 22lb (10kg) |
Mounting | Wall, desk, or rack mount, brackets, mounting Rack mount L brackets for front, rear, or wall installations; rubber feet for desk applications |
Cables | Molded IEC power inlet cord 7ft (200cm) |
nv-16ps10-pvd.pdf | Datasheet |
Call Now: 1-800-284-2288 |
|||||
Email Us: [email protected] |
|||||
|