ViewZ VZ-RPT repeater set (transmitter and receiver) extends over coax up to 1500 feet using 95 percent copper shielded RG6 or RG59.

VZ-RPT is designed t...

The Nitek Ethernet & PoE Extender EE328 is a single unit IP Network and PoE Repeater that requires very little installation time and absolutely no set up or configuration. Installa...

Size	1.1"H x 1.6"W x 3.6"D
Ethernet	100BaseTX Full Duplex
Power Requirements	PoE or PS48 Power Supply (48vdc @ 15.4watts)
Connection Method	RJ45
Clamping Voltage	15 Volts

The Toa Electronics EV-20RPS is a Digital Message Repeater, with a Rack-mount and 3 Minutes Storage Capacity. The EV-20RPS also Includes AD-246 AC Power Supply

The PT101H4 is a high-performance repeater and format converter for HDMI signals. The PT 101H4 combines previous HDMI formats and Ethernet to provide HDMI (v1.4 HE...

→ Input	1 HDMI connector, 1 Ethernet on an RJ-45 TP connector
→ Outputs	1 HDMI connector, 1 S/PDIF on an RCA connector
→ Bandwidth	Supports up to 2.25Gbps bandwidth per graphic channel
→ Compliance with HDMI Standard	Input: HDMI; output: HDMI and HDCP
→ Power Source	5V DC, 450mA

This item is no longer available.

The PT101HDCP is a line driver/repeater for DVI-D video signals. The PT 101HDCP reclocks ...

→ Input	1 DVI, 1.2Vpp on a DVI Molex 24-pin female connector; DDC signal 5Vpp (TTL)
→ Output	1 DVI, 1.2Vpp on DVI Molex 24-pin female connectors; DDC signal 5Vpp (TTL)
→ Bandwidth	Supports up to 2.25Gbps bandwidth
→ Power Source	5V DC, 180mA
→ Dimensions	6.22cm x 5.23cm x 3.20cm (2.5" x 2.1" x 1.3") W, D, H

The PT101Hxl is a line driver/repeater for HDMI video signals. The PT 101Hxl reclocks and equalizes the signal enabling multiple units to be cascaded.
 

→ Input	1 HDMI connector
→ Output	1 HDMI connector
→ Bandwidth	Supports up to 2.25Gbps bandwidth
→ Compliance With Standards	HDMI, HDCP
→ Power Source	5V DC, 120mA

The PT4iREX is an infrared signal repeater that can operate at distances of up to approximately 75m (240ft). The PT 4iREX extends infrared signals in areas where t...

→ Input	1 IR receiver
→ Outputs	4 IR emitters on 3.5mm mini connectors
→ Power Source	12V DC, 95mA
→ Dimensions	6.22cm x 5.24cm x 2.41cm (2.45" x 2.06" x 0.95") W, D, H
→ Weight	0.15kg (0.55lbs) approx

The TP-330FW is a twisted pair range extender/hub for FireWire® (IEEE 1394) signals. When used as a pair, one TP 330FW converts a FireWire® signal into a twisted...

→ Ports	2 FireWire® ports on 6-circuit FireWire® 400 connectors; 1 STP/UTP port on an RJ-45 connector
→ Transfer Rate	400Mbps
→ IEEE 1394 Standards	IEEE 1394a-2000, IEEE 1394-1995 @400Mbps max
→ ESD Line Protection	IEC 61000 4 2 (ESD) 15kV (air), 8kV (contact), IEC 61000 4 5 (lightning) 12A (8/20us), and IEC 61000 4 4 (EFT) 40A (5/50ns)
→ Power Source	12V DC, 60mA

The VA130FW is a high-performance bidirectional hub/repeater for 9-pin FireWire® 800 (IEEE 1394b) signals. The VA 130FW increases the number of ports available an...

→ Ports	2 FireWire® ports on 9-circuit FireWire® 800 connectors, 1 coax port on a BNC connector
→ Transfer Rate	800Mbps
→ IEEE 1394 Standards	IEEE 1394b-2002, IEEE 1394-1995, IEEE 1394b-2002 up to 800Mpbs
→ ESD Line Protection	IEC 61000-4-2 (ESD) 15kV (air), 8kV (contact), IEC 61000-4-5 (lightning) 12A (8/20us), and IEC 61000-4-4 (EFT) 40A (5/50ns)
→ Power Source	5V DC, 60mA

The VP-14 is a port extender for RS-232 data signals. The VP 14 sends data from any port to the other three.
 

The Datavideo VP-633 is a SDI repeater with DC power input.

Also Available:

The Datavideo VP-634 is a SDI repeater to use with VP-633. Can extend the signal for up to 100m.

Also Available:

The VS30FW is a high-performance bi-directional hub/repeater for 9-pin FireWire® 800 (IEEE 1394b) signals. The VS 30FW increases the number of ports available and...

→ Ports	3 bi-directional IEEE 1394b 800Mbps (S800) ports
→ Transfer Rate	100/200/400/800Mbps (S100, S200, S400, S800)
→ Standards	IEEE 1394-1995, IEEE P1394a, IEEE P1394b
→ Power Source	12V DC, 500mA or from the attached PC
→ Dimensions	12cm x 7.5cm x 2.5cm (4.7" x 2.95" x 0.98") W, D, H

The VS40FW is a high-performance bi-directional hub/repeater for 9-pin FireWire® 800 (IEEE 1394b) signals. The VS 40FW increases the number of ports available and...

→ Ports	4 bi-directional IEEE 1394b 800Mbps (S800) ports
→ Transfer Rate	100/200/400/800Mbps (S800, S400, S200, S100)
→ Standards	IEEE 1394-1995, IEEE P1394a, IEEE P1394b; fully supports the provisions of the IEEE P1394b Revision 1.33 at 1 Gigabit signaling rates; fully supports the provisions of the IEEE 1394-1995 Standard for High Performance Serial Bus and the P1394a Supplement; fully interoperable with FireWire™ and i.LINK™ implementation of IEEE Std 1394; provides three fully backward compatible (1394a 2000 fully compliant) bilingual P1394b cable ports at up to 800Mbps; fully compliant with OpenHCI requirements; provides three P1394b fully compliant cable ports at 100/200/400/800Mbps; full P1394a support includes: connection debounce, arbitrated short reset, multispeed concatenation, arbitration acceleration, fly-by concatenation, port disable/suspend/resume; extended resume signaling for compatibility with legacy DV devices
→ Power Source	12V DC, 1A
→ Dimensions	12cm x 7.5cm x 2.5cm (4.7" x 2.95" x 0.98") W, D, H

The VS−4FW is a high−performance bidirectional hub/repeater for 6−pin FireWire® (IEEE 1394) signals. It increases the number of ports available and/or extend the distance of...

→ Ports	VS-4FW: Four 6-pin serial 1394 Ports
→ Transfer Rate	100/200/400Mbps
→ Standards	IEEE 1394-1995, P1394a
→ Power Source	12V DC, 200mA
→ Dimensions	12cm x 7.5cm x 2.5cm (4.7" x 2.95" x 0.98") W, D, H

The VS−8FW is a high−performance bidirectional hub/repeater for 6−pin FireWire® (IEEE 1394) signals. It increases the number of ports available and/or extend the distance of...

→ Ports	Eight 6-pin serial 1394 Ports
→ Transfer Rate	100/200/400Mbps
→ Standards	IEEE 1394-1995, P1394a
→ Power Source	12V DC, 300mA
→ Dimensions	12cm x 7.5cm x 2.5cm (4.7" x 2.95" x 0.98") W, D, H